RAMA U80-A, wilba.tech WT60-A, WT65-A, WT80-A, IS31FL3736 driver (#3925)

* Initial commit of RAMA U80-A

* Initial commit of RAMA U80-A

* Moved IS31FL3736 driver, minor cleanups

* Superficial stuff

* Review changes

* Refactored to use common code.

drivers/issi/is31fl3736.c

@@ -0,0 +1,306 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+
+#ifdef __AVR__
+#include <avr/interrupt.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#else
+#include "wait.h"
+#endif
+
+#include "is31fl3736.h"
+#include <string.h>
+#include "i2c_master.h"
+#include "progmem.h"
+
+
+
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 00 <-> GND
+// 01 <-> SCL
+// 10 <-> SDA
+// 11 <-> VCC
+// ADDR1 represents A1:A0 of the 7-bit address.
+// ADDR2 represents A3:A2 of the 7-bit address.
+// The result is: 0b101(ADDR2)(ADDR1)
+#define ISSI_ADDR_DEFAULT 0x50
+
+#define ISSI_COMMANDREGISTER 0xFD
+#define ISSI_COMMANDREGISTER_WRITELOCK 0xFE
+#define ISSI_INTERRUPTMASKREGISTER 0xF0
+#define ISSI_INTERRUPTSTATUSREGISTER 0xF1
+
+#define ISSI_PAGE_LEDCONTROL 0x00 //PG0
+#define ISSI_PAGE_PWM 0x01        //PG1
+#define ISSI_PAGE_AUTOBREATH 0x02 //PG2
+#define ISSI_PAGE_FUNCTION 0x03   //PG3
+
+#define ISSI_REG_CONFIGURATION 0x00 //PG3
+#define ISSI_REG_GLOBALCURRENT 0x01 //PG3
+#define ISSI_REG_RESET 0x11// PG3
+#define ISSI_REG_SWPULLUP 0x0F //PG3
+#define ISSI_REG_CSPULLUP 0x10 //PG3
+
+#ifndef ISSI_TIMEOUT
+  #define ISSI_TIMEOUT 100
+#endif
+
+#ifndef ISSI_PERSISTENCE
+  #define ISSI_PERSISTENCE 0
+#endif
+
+// Transfer buffer for TWITransmitData()
+uint8_t g_twi_transfer_buffer[20];
+
+// These buffers match the IS31FL3736 PWM registers.
+// The control buffers match the PG0 LED On/Off registers.
+// Storing them like this is optimal for I2C transfers to the registers.
+// We could optimize this and take out the unused registers from these
+// buffers and the transfers in IS31FL3736_write_pwm_buffer() but it's
+// probably not worth the extra complexity.
+uint8_t g_pwm_buffer[DRIVER_COUNT][192];
+bool g_pwm_buffer_update_required = false;
+
+uint8_t g_led_control_registers[DRIVER_COUNT][24] = { { 0 }, { 0 } };
+bool g_led_control_registers_update_required = false;
+
+void IS31FL3736_write_register( uint8_t addr, uint8_t reg, uint8_t data )
+{
+    g_twi_transfer_buffer[0] = reg;
+    g_twi_transfer_buffer[1] = data;
+
+  #if ISSI_PERSISTENCE > 0
+    for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+      if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0)
+        break;
+    }
+  #else
+    i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
+  #endif
+}
+
+void IS31FL3736_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
+{
+    // assumes PG1 is already selected
+
+    // transmit PWM registers in 12 transfers of 16 bytes
+    // g_twi_transfer_buffer[] is 20 bytes
+
+    // iterate over the pwm_buffer contents at 16 byte intervals
+    for ( int i = 0; i < 192; i += 16 ) {
+        g_twi_transfer_buffer[0] = i;
+        // copy the data from i to i+15
+        // device will auto-increment register for data after the first byte
+        // thus this sets registers 0x00-0x0F, 0x10-0x1F, etc. in one transfer
+        for ( int j = 0; j < 16; j++ ) {
+            g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
+        }
+
+    #if ISSI_PERSISTENCE > 0
+      for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+        if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0)
+          break;
+      }
+    #else
+      i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
+    #endif
+    }
+}
+
+void IS31FL3736_init( uint8_t addr )
+{
+    // In order to avoid the LEDs being driven with garbage data
+    // in the LED driver's PWM registers, shutdown is enabled last.
+    // Set up the mode and other settings, clear the PWM registers,
+    // then disable software shutdown.
+
+    // Unlock the command register.
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+
+    // Select PG0
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
+    // Turn off all LEDs.
+    for ( int i = 0x00; i <= 0x17; i++ )
+    {
+        IS31FL3736_write_register( addr, i, 0x00 );
+    }
+
+    // Unlock the command register.
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+
+    // Select PG1
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
+    // Set PWM on all LEDs to 0
+    // No need to setup Breath registers to PWM as that is the default.
+    for ( int i = 0x00; i <= 0xBF; i++ )
+    {
+        IS31FL3736_write_register( addr, i, 0x00 );
+    }
+
+    // Unlock the command register.
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+
+    // Select PG3
+    IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_FUNCTION );
+    // Set global current to maximum.
+    IS31FL3736_write_register( addr, ISSI_REG_GLOBALCURRENT, 0xFF );
+    // Disable software shutdown.
+    IS31FL3736_write_register( addr, ISSI_REG_CONFIGURATION, 0x01 );
+
+    // Wait 10ms to ensure the device has woken up.
+    #ifdef __AVR__
+    _delay_ms( 10 );
+    #else
+    wait_ms(10);
+    #endif
+}
+
+void IS31FL3736_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
+{
+    if ( index >= 0 && index < DRIVER_LED_TOTAL ) {
+        is31_led led = g_is31_leds[index];
+
+        g_pwm_buffer[led.driver][led.r] = red;
+        g_pwm_buffer[led.driver][led.g] = green;
+        g_pwm_buffer[led.driver][led.b] = blue;
+        g_pwm_buffer_update_required = true;
+    }
+}
+
+void IS31FL3736_set_color_all( uint8_t red, uint8_t green, uint8_t blue )
+{
+    for ( int i = 0; i < DRIVER_LED_TOTAL; i++ )
+    {
+        IS31FL3736_set_color( i, red, green, blue );
+    }
+}
+
+void IS31FL3736_set_led_control_register( uint8_t index, bool red, bool green, bool blue )
+{
+    is31_led led = g_is31_leds[index];
+
+    // IS31FL3733
+    // The PWM register for a matrix position (0x00 to 0xBF) can be
+    // divided by 8 to get the LED control register (0x00 to 0x17),
+    // then mod 8 to get the bit position within that register.
+
+    // IS31FL3736
+    // The PWM register for a matrix position (0x00 to 0xBF) is interleaved, so:
+    // A1=0x00 A2=0x02 A3=0x04 A4=0x06 A5=0x08 A6=0x0A A7=0x0C A8=0x0E
+    // B1=0x10 B2=0x12 B3=0x14
+    // But also, the LED control registers (0x00 to 0x17) are also interleaved, so:
+    // A1-A4=0x00 A5-A8=0x01
+    // So, the same math applies.
+
+	uint8_t control_register_r = led.r / 8;
+	uint8_t control_register_g = led.g / 8;
+	uint8_t control_register_b = led.b / 8;
+
+	uint8_t bit_r = led.r % 8;
+	uint8_t bit_g = led.g % 8;
+	uint8_t bit_b = led.b % 8;
+
+    if ( red ) {
+        g_led_control_registers[led.driver][control_register_r] |= (1 << bit_r);
+    } else {
+        g_led_control_registers[led.driver][control_register_r] &= ~(1 << bit_r);
+    }
+    if ( green ) {
+        g_led_control_registers[led.driver][control_register_g] |= (1 << bit_g);
+    } else {
+        g_led_control_registers[led.driver][control_register_g] &= ~(1 << bit_g);
+    }
+    if ( blue ) {
+        g_led_control_registers[led.driver][control_register_b] |= (1 << bit_b);
+    } else {
+        g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
+    }
+
+    g_led_control_registers_update_required = true;
+
+}
+
+void IS31FL3736_mono_set_brightness( int index, uint8_t value )
+{
+    if ( index >= 0 && index < 96 ) {
+    	// Index in range 0..95 -> A1..A8, B1..B8, etc.
+    	// Map index 0..95 to registers 0x00..0xBE (interleaved)
+    	uint8_t pwm_register = index * 2;
+        g_pwm_buffer[0][pwm_register] = value;
+        g_pwm_buffer_update_required = true;
+    }
+}
+
+void IS31FL3736_mono_set_brightness_all( uint8_t value )
+{
+    for ( int i = 0; i < 96; i++ )
+    {
+    	IS31FL3736_mono_set_brightness( i, value );
+    }
+}
+
+void IS31FL3736_mono_set_led_control_register( uint8_t index, bool enabled )
+{
+	// Index in range 0..95 -> A1..A8, B1..B8, etc.
+
+	// Map index 0..95 to registers 0x00..0xBE (interleaved)
+	uint8_t pwm_register = index * 2;
+	// Map register 0x00..0xBE (interleaved) into control register and bit
+	uint8_t control_register = pwm_register / 8;
+	uint8_t bit = pwm_register % 8;
+
+    if ( enabled ) {
+        g_led_control_registers[0][control_register] |= (1 << bit);
+    } else {
+        g_led_control_registers[0][control_register] &= ~(1 << bit);
+    }
+
+    g_led_control_registers_update_required = true;
+}
+
+void IS31FL3736_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+{
+    if ( g_pwm_buffer_update_required )
+    {
+        // Firstly we need to unlock the command register and select PG1
+        IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
+
+        IS31FL3736_write_pwm_buffer( addr1, g_pwm_buffer[0] );
+        //IS31FL3736_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+    }
+    g_pwm_buffer_update_required = false;
+}
+
+void IS31FL3736_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+{
+    if ( g_led_control_registers_update_required )
+    {
+        // Firstly we need to unlock the command register and select PG0
+        IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
+        for ( int i=0; i<24; i++ )
+        {
+            IS31FL3736_write_register(addr1, i, g_led_control_registers[0][i] );
+            //IS31FL3736_write_register(addr2, i, g_led_control_registers[1][i] );
+        }
+    }
+}
+

drivers/issi/is31fl3736.h

@@ -0,0 +1,172 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include <stdint.h>
+#include <stdbool.h>
+
+
+// Simple interface option.
+// If these aren't defined, just define them to make it compile
+
+
+#ifndef DRIVER_COUNT
+#define DRIVER_COUNT 2
+#endif
+
+#ifndef DRIVER_LED_TOTAL
+#define DRIVER_LED_TOTAL 96
+#endif
+
+
+typedef struct is31_led {
+  uint8_t driver:2;
+  uint8_t r;
+  uint8_t g;
+  uint8_t b;
+} __attribute__((packed)) is31_led;
+
+extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
+
+void IS31FL3736_init( uint8_t addr );
+void IS31FL3736_write_register( uint8_t addr, uint8_t reg, uint8_t data );
+void IS31FL3736_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
+
+void IS31FL3736_set_color( int index, uint8_t red, uint8_t green, uint8_t blue );
+void IS31FL3736_set_color_all( uint8_t red, uint8_t green, uint8_t blue );
+
+void IS31FL3736_set_led_control_register( uint8_t index, bool red, bool green, bool blue );
+
+void IS31FL3736_mono_set_brightness( int index, uint8_t value );
+void IS31FL3736_mono_set_brightness_all( uint8_t value );
+void IS31FL3736_mono_set_led_control_register( uint8_t index, bool enabled );
+
+// This should not be called from an interrupt
+// (eg. from a timer interrupt).
+// Call this while idle (in between matrix scans).
+// If the buffer is dirty, it will update the driver with the buffer.
+void IS31FL3736_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3736_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+
+#define A_1  0x00
+#define A_2  0x02
+#define A_3  0x04
+#define A_4  0x06
+#define A_5  0x08
+#define A_6  0x0A
+#define A_7  0x0C
+#define A_8  0x0E
+
+#define B_1  0x10
+#define B_2  0x12
+#define B_3  0x14
+#define B_4  0x16
+#define B_5  0x18
+#define B_6  0x1A
+#define B_7  0x1C
+#define B_8  0x1E
+
+#define C_1  0x20
+#define C_2  0x22
+#define C_3  0x24
+#define C_4  0x26
+#define C_5  0x28
+#define C_6  0x2A
+#define C_7  0x2C
+#define C_8  0x2E
+
+#define D_1  0x30
+#define D_2  0x32
+#define D_3  0x34
+#define D_4  0x36
+#define D_5  0x38
+#define D_6  0x3A
+#define D_7  0x3C
+#define D_8  0x3E
+
+#define E_1  0x40
+#define E_2  0x42
+#define E_3  0x44
+#define E_4  0x46
+#define E_5  0x48
+#define E_6  0x4A
+#define E_7  0x4C
+#define E_8  0x4E
+
+#define F_1  0x50
+#define F_2  0x52
+#define F_3  0x54
+#define F_4  0x56
+#define F_5  0x58
+#define F_6  0x5A
+#define F_7  0x5C
+#define F_8  0x5E
+
+#define G_1  0x60
+#define G_2  0x62
+#define G_3  0x64
+#define G_4  0x66
+#define G_5  0x68
+#define G_6  0x6A
+#define G_7  0x6C
+#define G_8  0x6E
+
+#define H_1  0x70
+#define H_2  0x72
+#define H_3  0x74
+#define H_4  0x76
+#define H_5  0x78
+#define H_6  0x7A
+#define H_7  0x7C
+#define H_8  0x7E
+
+#define I_1  0x80
+#define I_2  0x82
+#define I_3  0x84
+#define I_4  0x86
+#define I_5  0x88
+#define I_6  0x8A
+#define I_7  0x8C
+#define I_8  0x8E
+
+#define J_1  0x90
+#define J_2  0x92
+#define J_3  0x94
+#define J_4  0x96
+#define J_5  0x98
+#define J_6  0x9A
+#define J_7  0x9C
+#define J_8  0x9E
+
+#define K_1  0xA0
+#define K_2  0xA2
+#define K_3  0xA4
+#define K_4  0xA6
+#define K_5  0xA8
+#define K_6  0xAA
+#define K_7  0xAC
+#define K_8  0xAE
+
+#define L_1  0xB0
+#define L_2  0xB2
+#define L_3  0xB4
+#define L_4  0xB6
+#define L_5  0xB8
+#define L_6  0xBA
+#define L_7  0xBC
+#define L_8  0xBE
+

keyboards/rama/readme.md

@@ -6,4 +6,6 @@ Firmware for keyboards designed by [RAMA WORKS](https://rama.works)
 
 [RAMA M60-A](https://rama.works/#/m60-a/)
 
+[RAMA U80-A](https://rama.works/#/tkl-a/)
+
 [RAMA M10-B](https://www.massdrop.com/buy/rama-m10-a?mode=guest_open)

keyboards/rama/u80_a/config.h

@@ -0,0 +1,187 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x5241 // "RW"
+#define PRODUCT_ID      0x080A // 80-A
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    RAMA.WORKS
+#define PRODUCT         RAMA U80-A
+#define DESCRIPTION     RAMA U80-A Keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 17
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F1, F0, E6, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4, B7, B0 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION ROW2COL
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+

keyboards/rama/u80_a/keymaps/default/keymap.c

@@ -0,0 +1,22 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	  [0] = LAYOUT_all(
+	    KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,                    KC_PSCR, KC_SLCK, KC_PAUS,
+	    KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_BSPC, KC_INS,  KC_HOME, KC_PGUP,
+	    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_DEL,  KC_END,  KC_PGDN,
+	    KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_TRNS,                            KC_UP,
+	    KC_LCTL, KC_LGUI, KC_LALT,                   KC_SPC,                                      KC_RALT, KC_RGUI, KC_APP,  KC_RCTL,          KC_LEFT, KC_DOWN, KC_RGHT),
+
+	  [1] = LAYOUT_all(
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,                                     KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+};
+

keyboards/rama/u80_a/readme.md

@@ -0,0 +1,15 @@
+# RAMA U80-A
+
+![RAMA U80-A](https://something.com/something.jpg)
+
+A TKL keyboard. [More info at RAMA WORKS](https://rama.works/#/tkl-a/)
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: RAMA U80-A PCB  
+Hardware Availability: [RAMA WORKS Store](https://ramaworks.store/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make rama/u80_a:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/rama/u80_a/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	drivers/issi/is31fl3736.c \
+		drivers/avr/i2c_master.c \
+		keyboards/wilba_tech/wt_mono_backlight.c \
+		keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches

keyboards/rama/u80_a/u80_a.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/rama/u80_a/u80_a.h

@@ -0,0 +1,43 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+// Right switch of split backspace is at 3,13 and is the only switch
+// whose physical position doesn't match switch matrix position :-(
+// However, it also makes no sense to view the physical as 18 columns,
+// so the numbering goes 00 to 16. Deal with it.
+
+#define LAYOUT_all( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012,             K014, K015, K016, \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K313, K114, K115, K116, \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213,       K214, K215, K216, \
+    K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,                               \
+    K400,       K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413,             K415,       \
+    K500, K501, K502,                   K506,                   K510, K511, K512, K513,       K514, K515, K516  \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, ____, K014, K015, K016 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216 }, \
+    { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, ____, ____, ____ }, \
+	{ K400, ____, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, ____, K415, ____ }, \
+    { K500, K501, K502, ____, ____, ____, K506, ____, ____, ____, K510, K511, K512, K513, K514, K515, K516 }  \
+}
+

keyboards/wilba_tech/wt60_a/config.h

@@ -0,0 +1,187 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6582 // wilba.tech
+#define PRODUCT_ID      0x060A // 60-A
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    wilba.tech
+#define PRODUCT         wilba.tech WT60-A
+#define DESCRIPTION     wilba.tech WT60-A
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F0, E6, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION ROW2COL
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+

keyboards/wilba_tech/wt60_a/keymaps/ansi_split_bs_rshift/keymap.c

@@ -0,0 +1,38 @@
+// ANSI split backspace/right shift layout for WT60-A
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+// Default layer
+[0] = LAYOUT_60_ansi_split_bs_rshift(
+	KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_DEL,
+	KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC,
+	KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, MO(1),
+	KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, KC_APP, KC_RCTL),
+
+// Fn1 Layer
+[1] = LAYOUT_60_ansi_split_bs_rshift(
+	KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_INS, KC_DEL,
+	KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP,   KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_EJCT, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END,  KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn2 Layer
+[2] = LAYOUT_60_ansi_split_bs_rshift(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn3 Layer
+[3] = LAYOUT_60_ansi_split_bs_rshift(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};

keyboards/wilba_tech/wt60_a/keymaps/default/keymap.c

@@ -0,0 +1,38 @@
+// Default layout for WT60-A
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+// Default layer
+[0] = LAYOUT_60_ansi(
+	KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,
+	KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
+	KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,
+	KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1),   KC_RCTL),
+
+// Fn1 Layer
+[1] = LAYOUT_60_ansi(
+	KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL ,
+	KC_CAPS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS,  KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS,
+	KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END,  KC_PGDN, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn2 Layer
+[2] = LAYOUT_60_ansi(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn3 Layer
+[3] = LAYOUT_60_ansi(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};

keyboards/wilba_tech/wt60_a/readme.md

@@ -0,0 +1,15 @@
+# WILBA.TECH WT60-A
+
+![WILBA.TECH WT60-A](https://wilba.tech)
+
+WT60-A is a keyboard PCB supporting 60% layout. [More info at wilba.tech](https://wilba.tech/)
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: WILBA.TECH WT65-A  
+Hardware Availability: Custom keyboard group buys
+
+Make example for this keyboard (after setting up your build environment):
+
+    make wilba_tech/wt60_a:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/wilba_tech/wt60_a/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	drivers/issi/is31fl3736.c \
+		drivers/avr/i2c_master.c \
+		keyboards/wilba_tech/wt_mono_backlight.c \
+		keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches

keyboards/wilba_tech/wt60_a/wt60_a.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/wilba_tech/wt60_a/wt60_a.h

@@ -0,0 +1,52 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+#define LAYOUT_60_ansi_split_bs_rshift( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K213, \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             \
+    K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+    K400, K401, K402,                   K406,                   K410, K411, K412, K413        \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213 }, \
+	{ K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313 }, \
+    { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413 }  \
+}
+
+#define LAYOUT_60_ansi( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013,  \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,       \
+    K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,       \
+    K400, K401, K402,                   K406,                   K410, K411, K412, K413  \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, ____ }, \
+	{ K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, ____ }, \
+    { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413 }  \
+}
+
+
+

keyboards/wilba_tech/wt65_a/config.h

@@ -0,0 +1,187 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6582 // wilba.tech
+#define PRODUCT_ID      0x065A // 65-A
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    wilba.tech
+#define PRODUCT         wilba.tech WT65-A
+#define DESCRIPTION     wilba.tech WT65-A
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F0, E6, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION ROW2COL
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+

keyboards/wilba_tech/wt65_a/keymaps/default/keymap.c

@@ -0,0 +1,37 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	// Default layer
+	[0] = LAYOUT_all(
+		KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_BSPC, KC_HOME,
+		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_PGUP,
+		KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,                    KC_PGDN,
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,                   KC_UP,   KC_END,
+		KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, MO(1),            KC_LEFT, KC_DOWN, KC_RGHT),
+
+	// Fn1 Layer
+	[1] = LAYOUT_all(
+		KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_DEL,  KC_TRNS,
+		KC_CAPS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS,  KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END,  KC_PGDN, KC_TRNS,                   KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn2 Layer
+	[2] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn3 Layer
+	[3] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+};
+

keyboards/wilba_tech/wt65_a/readme.md

@@ -0,0 +1,15 @@
+# WILBA.TECH WT65-A
+
+![WILBA.TECH WT65-A](https://wilba.tech)
+
+WT65-A is a keyboard PCB supporting 65% layout with 0.25U blocker. [More info at wilba.tech](https://wilba.tech/)
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: WILBA.TECH WT65-A  
+Hardware Availability: Custom keyboard group buys
+
+Make example for this keyboard (after setting up your build environment):
+
+    make wilba_tech/wt65_a:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/wilba_tech/wt65_a/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	drivers/issi/is31fl3736.c \
+		drivers/avr/i2c_master.c \
+		keyboards/wilba_tech/wt_mono_backlight.c \
+		keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches

keyboards/wilba_tech/wt65_a/wt65_a.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/wilba_tech/wt65_a/wt65_a.h

@@ -0,0 +1,41 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+// Right switch of split backspace is at 2,13 and is the only switch
+// whose physical position doesn't match switch matrix position :-(
+// However, it also makes no sense to view the physical as 16 columns,
+// so the numbering goes 00 to 14. Deal with it.
+
+#define LAYOUT_all( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K213, K014, \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       K114, \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             K214, \
+    K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,             K313, K314, \
+    K400, K401, K402,                   K406,                   K410, K411,       K412, K413, K414  \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \
+	{ K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314 }, \
+    { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413, K414 }  \
+}
+

keyboards/wilba_tech/wt80_a/config.h

@@ -0,0 +1,187 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6582 // wilba.tech
+#define PRODUCT_ID      0x080A // 80-A
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    wilba.tech
+#define PRODUCT         wilba.tech WT80-A
+#define DESCRIPTION     wilba.tech WT80-A
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 17
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F1, F0, E6, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4, B7, B0 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION ROW2COL
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+

keyboards/wilba_tech/wt80_a/keymaps/default/keymap.c

@@ -0,0 +1,22 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	  [0] = LAYOUT_all(
+	    KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,                    KC_PSCR, KC_SLCK, KC_PAUS,
+	    KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_BSPC, KC_INS,  KC_HOME, KC_PGUP,
+	    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_DEL,  KC_END,  KC_PGDN,
+	    KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_TRNS,                            KC_UP,
+	    KC_LCTL, KC_LGUI, KC_LALT,                   KC_SPC,                                      KC_RALT, KC_RGUI, KC_APP,  KC_RCTL,          KC_LEFT, KC_DOWN, KC_RGHT),
+
+	  [1] = LAYOUT_all(
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,
+	    KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,                                     KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+};
+

keyboards/wilba_tech/wt80_a/readme.md

@@ -0,0 +1,15 @@
+# WILBA.TECH WT80-A
+
+![WILBA.TECH WT80-A](https://wilba./tech)
+
+WT80-A is a keyboard PCB supporting TKL layout with 0.25U gaps. [More info at wilba.tech](https://wilba.tech/)
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: WILBA.TECH WT80-A  
+Hardware Availability: Custom keyboard group buys
+
+Make example for this keyboard (after setting up your build environment):
+
+    make wilba_tech/wt80_a:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/wilba_tech/wt80_a/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	drivers/issi/is31fl3736.c \
+		drivers/avr/i2c_master.c \
+		keyboards/wilba_tech/wt_mono_backlight.c \
+		keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches

keyboards/wilba_tech/wt80_a/wt80_a.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/wilba_tech/wt80_a/wt80_a.h

@@ -0,0 +1,43 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+// Right switch of split backspace is at 3,13 and is the only switch
+// whose physical position doesn't match switch matrix position :-(
+// However, it also makes no sense to view the physical as 18 columns,
+// so the numbering goes 00 to 16. Deal with it.
+
+#define LAYOUT_all( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012,             K014, K015, K016, \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K313, K114, K115, K116, \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213,       K214, K215, K216, \
+    K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,                               \
+    K400,       K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413,             K415,       \
+    K500, K501, K502,                   K506,                   K510, K511, K512, K513,       K514, K515, K516  \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, ____, K014, K015, K016 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216 }, \
+    { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, ____, ____, ____ }, \
+	{ K400, ____, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, ____, K415, ____ }, \
+    { K500, K501, K502, ____, ____, ____, K506, ____, ____, ____, K510, K511, K512, K513, K514, K515, K516 }  \
+}
+

keyboards/wilba_tech/wt_main.c

@@ -0,0 +1,55 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "quantum.h"
+#include "keyboards/wilba_tech/wt_mono_backlight.h"
+
+void bootmagic_lite(void)
+{
+	// The lite version of TMK's bootmagic.
+	// 100% less potential for accidentally making the
+	// keyboard do stupid things.
+
+	// We need multiple scans because debouncing can't be turned off.
+	matrix_scan();
+	wait_ms(DEBOUNCING_DELAY);
+	wait_ms(DEBOUNCING_DELAY);
+	matrix_scan();
+
+	// If the Esc (matrix 0,0) is held down on power up,
+	// reset the EEPROM valid state and jump to bootloader.
+	if ( matrix_get_row(0) & (1<<0) ) {
+		// Set the TMK/QMK EEPROM state as invalid.
+		eeconfig_disable();
+		// Jump to bootloader.
+		bootloader_jump();
+	}
+}
+
+void matrix_init_kb(void)
+{
+	bootmagic_lite();
+	backlight_init_drivers();
+	backlight_timer_init();
+	backlight_timer_enable();
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void)
+{
+	backlight_update_pwm_buffers();
+	matrix_scan_user();
+}

keyboards/wilba_tech/wt_mono_backlight.c

@@ -0,0 +1,116 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "wt_mono_backlight.h"
+#include "drivers/avr/i2c_master.h"
+#include "drivers/issi/is31fl3736.h"
+
+#include <avr/interrupt.h>
+
+#define ISSI_ADDR_DEFAULT 0x50
+
+bool g_suspend_state = false;
+
+// Global tick at 20 Hz
+uint32_t g_tick = 0;
+uint8_t g_config_effect_speed = 0;
+uint8_t g_config_brightness = 255;
+
+void backlight_init_drivers(void)
+{
+	// Initialize I2C
+	i2c_init();
+	IS31FL3736_init( ISSI_ADDR_DEFAULT );
+
+	for ( uint8_t index = 0; index < 96; index++ )	{
+		IS31FL3736_mono_set_led_control_register( index, true );
+	}
+	IS31FL3736_update_led_control_registers( ISSI_ADDR_DEFAULT, 0x00 );
+}
+
+
+// This is (F_CPU/1024) / 20 Hz
+// = 15625 Hz / 20 Hz
+// = 781
+#define TIMER3_TOP 781
+
+void backlight_timer_init(void)
+{
+	static uint8_t backlight_timer_is_init = 0;
+	if ( backlight_timer_is_init ) {
+		return;
+	}
+	backlight_timer_is_init = 1;
+
+	// Timer 3 setup
+	TCCR3B = _BV(WGM32) | 			// CTC mode OCR3A as TOP
+			 _BV(CS32) | _BV(CS30); // prescale by /1024
+	// Set TOP value
+	uint8_t sreg = SREG;
+	cli();
+
+	OCR3AH = (TIMER3_TOP >> 8) & 0xff;
+	OCR3AL = TIMER3_TOP & 0xff;
+	SREG = sreg;
+}
+
+void backlight_timer_enable(void)
+{
+	TIMSK3 |= _BV(OCIE3A);
+}
+
+void backlight_timer_disable(void)
+{
+	TIMSK3 &= ~_BV(OCIE3A);
+}
+
+void backlight_set_suspend_state(bool state)
+{
+	g_suspend_state = state;
+}
+
+void backlight_effect_cycle_all(void)
+{
+	uint8_t offset = ( g_tick << g_config_effect_speed ) & 0xFF;
+
+	backlight_set_brightness_all( offset );
+}
+
+ISR(TIMER3_COMPA_vect)
+{
+	// delay 1 second before driving LEDs or doing anything else
+	static uint8_t startup_tick = 0;
+	if ( startup_tick < 20 ) {
+		startup_tick++;
+		return;
+	}
+
+	g_tick++;
+
+	//backlight_effect_cycle_all();
+	backlight_set_brightness_all( 255 );
+}
+
+void backlight_update_pwm_buffers(void)
+{
+	IS31FL3736_update_pwm_buffers(ISSI_ADDR_DEFAULT,0x00);
+}
+
+void backlight_set_brightness_all( uint8_t value )
+{
+	IS31FL3736_mono_set_brightness_all( value );
+}
+

keyboards/wilba_tech/wt_mono_backlight.h

@@ -0,0 +1,33 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include <stdint.h>
+#include <stdbool.h>
+
+void backlight_init_drivers(void);
+
+void backlight_timer_init(void);
+void backlight_timer_enable(void);
+void backlight_timer_disable(void);
+
+void backlight_set_suspend_state(bool state);
+
+void backlight_update_pwm_buffers(void);
+
+void backlight_set_brightness_all( uint8_t value );
+