Merge pull request #541 from milestogo/master

initial kinisis advantage build

keyboards/handwired/traveller/Makefile

@@ -0,0 +1,89 @@
+
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+# for avr upload
+USB ?= /dev/cu.usbmodem1421
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+ifdef TEENSY2
+    OPT_DEFS += -DATREUS_TEENSY2
+    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+else
+    OPT_DEFS += -DATREUS_ASTAR
+    OPT_DEFS += -DCATERINA_BOOTLOADER
+    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+endif
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# MCU name
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+RGBLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+upload: build
+	$(ATREUS_UPLOAD_COMMAND)
+

keyboards/handwired/traveller/config.h

@@ -0,0 +1,173 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    You
+#define PRODUCT         traveller
+#define DESCRIPTION     A custom keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 4 
+#define MATRIX_COLS 13 
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, D3, D2 }
+ // no I can't say why this order seemed like a good idea
+#define MATRIX_COL_PINS { B5, D6, B7, B6, F6, B1, B3, F7, B4, E6, D7, C6, D4 }
+#define UNUSED_PINS
+
+// LED stuff
+#define RGB_DI_PIN B2
+//#define RBLIGHT_TIMER
+#define RGBLED_NUM 1     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif

keyboards/handwired/traveller/keymaps/default/keymap.c

@@ -0,0 +1,305 @@
+#include "traveller.h"
+#include "mousekey.h"
+#include "action_layer.h"
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+#define _QW 0
+#define _LW 1
+#define _HI 2
+#define _NAV 4
+#define _CUR 5
+#define _FKEYS 6 
+#define _TRNS 8
+
+// We do the same trick for functions
+#define  RGBLED_TOGGLE 10
+#define _HIOUT 15
+#define _LWOUT 16
+// Macros
+#define  MDL 4
+#define  MDR 5
+#define  MUR 6
+#define  MUL 3 
+
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | NAV  | ` ~  |   W  |   E  |   R  |   T  |      |  Y   |   U  |   I  |   O  |  -   |  =   |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * | Tab  |   Q  |   S  |   D  |   F  |   G  |      |  H   |  J   |   K  |   L  |   P  |  \   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ *|ctrl/esc|  A  |   X  |   C  |   V  |   B  |Ctrl /|   N  |   M  |   ,  |   .  |   ;  |  '   |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * | Shift|   Z  | Del  | GUI  | Low  | Bspc |/Enter| Spc  | Hi   | GUI  | Alt  |  /   |Shift |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+[_QW] = KEYMAP( 
+  F(_NAV),          KC_GRV, KC_W,    KC_E,    KC_R,    KC_T,             KC_Y,    KC_U,    KC_I,    KC_O,    KC_MINS,  KC_EQL,
+  KC_TAB,           KC_Q,    KC_S,    KC_D,    KC_F,    KC_G,            KC_H,    KC_J,    KC_K,    KC_L,    KC_P, 	KC_BSLS,
+  CTL_T(KC_ESC),    KC_A,    KC_X,    KC_C,    KC_V,    KC_B,    KC_RCTL,  KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SCLN, 	KC_QUOT,
+  KC_LSFT, KC_Z,    KC_DEL, KC_LGUI, MO(_LW), KC_BSPC, KC_ENTER, KC_SPC,  MO(_HI), KC_RGUI, KC_RALT,    KC_SLSH,   KC_RSFT
+ ),
+
+/* LOW  - numbers, missing or awkward programming keys
+ Doubled 1 key allows lazy reach with ring finger. 
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | FKeys|   1  |   2  |  3   |   4  |   5  |      |  6   |  7   |   8  |   9  |   0  |Ctrl-alt-del|
+ * |------+------+------+------+------+------|      +------+------+------+------+------+------|
+ * | Tab  |   1  |  ]   |  (   |  )   |      |      |   *  |   (  |   )  |   [  |      |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * | Caps |  [   |      |  {   |   }  |  `   |     /|   #  |   {  |   }  |      | ]    |      |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * | Shift|      |      |      | Low  |      |/     |      |  Hi  |      |      |      |Shift |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_LW] = KEYMAP( 
+  F(_FKEYS),   KC_1,     KC_2,      KC_3,     KC_4,    KC_5,             KC_6,    KC_7,       KC_8,      KC_9,    KC_0,  LCTL(LALT(KC_DEL)) ,
+  KC_TRNS,  KC_1,     KC_RBRC,   KC_LPRN,  KC_RPRN, KC_NO,               KC_ASTR, KC_LPRN,    KC_RPRN,    KC_LBRC,    KC_NO, KC_NO,
+  KC_CAPS,   KC_LBRC,  KC_NO,     KC_LCBR,  KC_RCBR, KC_TILD,   KC_TRNS,  KC_HASH, KC_LCBR,    KC_RCBR,   KC_NO,    KC_RBRC,   KC_NO,
+  KC_TRNS,  KC_TRNS,  KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,  KC_TRNS
+),
+
+/* HI - Punctuation, shell and 
+url ://@.com  row on bottom,    && is opposite ||       ^$ are in regex order: ^.*$    
+Right hand nav keys work pretty well chorded with the Right hand Hi Key
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * |FKEYS |   !  |   @  |   #  |   $  |   %  |      |  ^   |   &  |   *  |   (  |   )  |   +  |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |      |  !   |  &   |  "|" |   $  |   %  |      |  Vol+|  Mute|      |      |      |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * | CAPS |  ^   |   :  |   .  |   *  |   -  |     /|  Vol-| Play | PgUp | Home | Up   | End  |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |      |   /  |      |      | Low  |      |/     |      |  Hi  | PgDn | Left| Down | Right |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_HI] = KEYMAP( 
+ F(_FKEYS), KC_EXLM,  KC_AT,   KC_HASH,  KC_DLR,   KC_PERC,           KC_CIRC,  KC_AMPR,    KC_ASTR,   KC_LPRN,  KC_RPRN,  KC_PLUS,
+ KC_TRNS, KC_EXLM,  KC_AMPR, KC_PIPE,  KC_DLR,   KC_PERC,             KC_VOLU, KC_MUTE,    KC_NO,     KC_NO,    KC_NO,    KC_NO, 
+ KC_CAPS, KC_CIRC,  KC_COLN,  KC_DOT,  KC_ASTR,  KC_MINS,   KC_TRNS,  KC_VOLD, KC_PPLS,    KC_PGUP,   KC_HOME,  KC_UP,    KC_END,
+ KC_TRNS, KC_SLSH,  KC_TRNS,  KC_TRNS, F(_LW),   KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,    KC_PGDN,   KC_LEFT,  KC_DOWN,  KC_RIGHT 
+),	
+
+/* NAV - mouse &  navigation
+//gui left and right are line home/end, or fore & back in browser
+// Mouse buttons are reversed for comfort - bigger stretch is to the right button. 
+
+ * ,-----------------------------------------.      .-----------------------------------------.
+* | NAV  |      |      | Up   |      |Gui-> |      | MwU  | MS_UL| MS_U |MS_UR |      |Ms Norm|
+* |------+------+------+------+------+------|      |------+------+------+------+------+--------|
+* |      |Gui<- | Left | Down |Right | C^E  |      | BTN3 | MS_L |MS Up | MS_R |      |Ms Fast |
+* |------+------+------+------+------+------|------|------+------+------+------+------+--------|
+* |      | C^A  | GUI X| GUI C| GUI_V|      |Enter/| MWD  | M_DL |MS Dwn|MS_DR | Up   |Ms Slow |
+* |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+* |      | GuiZ |      |      | Low  |      |/ButnR|ButnL |  Hi  |      | Left | Down | Right |
+* `------------------------------------------------------------------------------------------'
+*/
+
+[_NAV] = KEYMAP( 
+  F(_NAV),  KC_NO,         KC_NO,    KC_UP,       KC_NO,     RGUI(KC_RIGHT),            KC_WH_U,  M(MUL), KC_MS_U,   M(MUR), KC_NO, KC_ACL2,
+  KC_TRNS, RGUI(KC_LEFT),  KC_LEFT,  KC_DOWN,     KC_RIGHT,  LCTL(KC_E),                KC_BTN3,  KC_MS_L,  KC_MS_U,   KC_MS_R,  KC_NO, KC_ACL1,
+  KC_TRNS, LCTL(KC_A),     LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO,         KC_ENTER,   KC_WH_D,  M(MDL), KC_MS_D,  M(MDR),  KC_UP, KC_ACL0,
+  KC_TRNS, RGUI(KC_Z),     KC_TRNS,  KC_TRNS,     KC_TRNS,   KC_TRNS,       KC_BTN2,   KC_BTN1,  KC_TRNS,  KC_TRNS,   KC_LEFT,   KC_DOWN,   KC_RIGHT
+),
+
+/* FKEYS - Funtion keys & mac stuff
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | FKEYS| F1   | F2   | F3   |  F4  | F5   |      | F6   | F7   | F8   | F9   | F10  | Ctrl | 
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |      |      |      |      |      |      |      |  F11 | F12  |  F13 | F14  |  F15 | Alt  |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * |Qwerty|      |      |      |      |      |     /|      |      |      |      |      | Del  |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |    . |RGBTog|  .   |      | LO   | Bspc |/     |      | HI   |      |      |      |      |
+ * `------------------------------------------------------------------------------------------'
+ *
+ */ 
+ 
+[_FKEYS] = KEYMAP( 
+  F(_FKEYS), KC_F1,    KC_F2,  	KC_F3,      KC_F4,     KC_F5,               KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,    KC_RCTL,
+  KC_TRNS,   KC_NO,    KC_NO,   KC_NO,      KC_NO,     KC_NO,               KC_F11,   KC_F12,   KC_F13,    KC_F14,  KC_F15,  	 KC_LALT ,
+  F(_QW),   KC_NO,     KC_NO,   KC_NO,      KC_NO,     KC_NO,    KC_TRNS,   KC_NO,    KC_NO,    KC_NO,      KC_NO,   KC_NO,    KC_DEL,
+  KC_TRNS, F(RGBLED_TOGGLE),    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,   KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS
+),
+
+
+/* TRNS - skeleton for laters
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * |   .  |   .  |   .  |   .  |   .  |   .  |      |  ^   |   &  |   *  |   (  |   )  |      |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |   .  |   .  |   .  |   .  |   .  |   .  |      |  6   |  7   |   8  |   9  |   0  |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * |   .  |   .  |   .  |   .  |   .  |   .  |     /|      |      |      |   .  |   ;  |  "   |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |    . |   .  |  .   | GUI  |  LO  |   .  |/     | Spc  |  HI  | GUI  |  M0  |  /   |LSFT |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_TRNS] = {
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS},
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS},
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS},
+  {KC_TRNS, KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS}
+ }
+
+
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+    [_QW] = ACTION_LAYER_ON(_QW,ON_RELEASE), // return to QWERTY  layer
+    [_LW] = ACTION_LAYER_TAP_TOGGLE(_LW), // Turn on LW when holding, or tap 3 times to switch
+    [_HI] = ACTION_LAYER_TAP_TOGGLE(_HI), // Turn on LW when holding, or tap 3 times to switch               
+    [_NAV] = ACTION_LAYER_TOGGLE(_NAV),                                   
+    [_FKEYS] = ACTION_LAYER_TOGGLE(_FKEYS),  
+    [_LWOUT] = ACTION_LAYER_OFF(_LW,ON_RELEASE),
+    [_HIOUT] = ACTION_LAYER_OFF(_HI,ON_RELEASE),
+    
+    // Functions
+  [RGBLED_TOGGLE]  = ACTION_FUNCTION(RGBLED_TOGGLE),
+ 
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+            #ifdef BACKLIGHT_ENABLE
+              backlight_step();
+            #endif
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+
+   // from  algernon's ErgoDox EZ layout,
+       case MUL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case MUR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+
+      case MDL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case MDR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+
+
+      }
+    return MACRO_NONE;
+};
+
+
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  switch (id) {
+    case RGBLED_TOGGLE:
+      //led operations
+      if (record->event.pressed) {
+        rgblight_toggle();
+      }
+        break;
+  }
+}
+
+ 
+
+void LayerLEDSet(uint8_t layr) {
+
+    switch (layr) {
+        case _QW:
+            rgblight_setrgb(0,20, 0); //  dim green
+        break;
+        case _LW:
+            // deep purple
+            rgblight_setrgb(20,0,35); 
+            break;  
+        case _HI:
+            // light blue
+           rgblight_setrgb(0,20,20); 
+            break;    
+        case _NAV:
+            // Yellowy orange
+            rgblight_setrgb(25,20,0); // brighter
+            break;
+        case _FKEYS:
+         // RED
+           rgblight_setrgb(20,0,0); // brighter
+            break;  
+        default:
+            rgblight_setrgb(20,2,20);//error
+            break;
+    }
+ 
+ return;
+  
+}
+
+void matrix_init_user(void) {
+}
+
+// Bleah globals need to be initialized.
+uint8_t old_layer=_QW;
+
+void matrix_scan_user(void) {
+         uint8_t layer = biton32(layer_state);
+         if (old_layer != layer) {
+           LayerLEDSet(layer);
+           old_layer=layer;
+           }
+}
+
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}
+
+

keyboards/handwired/traveller/keymaps/default/readme.md

@@ -0,0 +1,2 @@
+# The default keymap for handwired/traveller
+this is a kitchen sink build 

keyboards/handwired/traveller/readme.md

@@ -0,0 +1,35 @@
+traveler keyboard firmware
+======================
+
+## Traveller Specific Info ##
+The traveller is a varient on the atreus keyboard. 
+Like the Atreus, it is designed to be a good compromise between size and ergonomics. 
+
+key differences are 
+- an additional column for each pinky
+- an RGB LED in the center to show the current layer
+- more finger stagger,  splay angle and contoured keycaps (F2 profile for space key). 
+
+You can make your own traveller  keyboard by using the openscad tools from the atreus repository, and adding a hole for the LED to shine through. 
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent README.md](/README.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboard/traveler folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top README.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.

keyboards/handwired/traveller/traveller.c

@@ -0,0 +1,61 @@
+#include "traveller.h"
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+        // leave this function blank - it can be defined in a keymap file
+};
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+__attribute__ ((weak))
+void process_action_user(keyrecord_t *record) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+__attribute__ ((weak))
+void led_set_user(uint8_t usb_led) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+void matrix_init_kb(void) {
+        // put your keyboard start-up code here
+        // runs once when the firmware starts up
+
+#ifdef RGBLIGHT_ENABLE
+        rgblight_init();
+        rgblight_mode(1); // solid, no timer
+        rgblight_setrgb(0,20,0);// dim green, happens to be same as _QW
+#endif
+
+// Turn status LED on
+        DDRC |= (1<<7);
+        PORTC |= (1<<7);
+
+        matrix_init_user();
+}
+
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}
+
+

keyboards/handwired/traveller/traveller.h

@@ -0,0 +1,32 @@
+#ifndef TRAVELLER_H
+#define TRAVELLER_H
+
+#include "quantum.h"
+#include "led.h"
+
+#ifdef RGBLIGHT_ENABLE
+  #include "rgblight.h"
+#endif
+#ifdef BACKLIGHT_ENABLE
+        #include "backlight.h"
+#endif
+
+
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+#define KEYMAP( \
+        k00, k01, k02, k03, k04, k05,       k07, k08, k09, k0a, k0b, k0c, \
+        k10, k11, k12, k13, k14, k15,       k17, k18, k19, k1a, k1b, k1c, \
+        k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \
+        k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c  \
+) \
+{ \
+        { k00, k01, k02, k03, k04, k05, KC_NO, k07, k08, k09, k0a, k0b, k0c }, \
+        { k10, k11, k12, k13, k14, k15, KC_NO, k17, k18, k19, k1a, k1b, k1c }, \
+        { k20, k21, k22, k23, k24, k25, k26,   k27, k28, k29, k2a, k2b, k2c }, \
+        { k30, k31, k32, k33, k34, k35, k36,   k37, k38, k39, k3a, k3b, k3c } \
+}
+
+#endif

keyboards/kinesis/Makefile

@@ -0,0 +1,79 @@
+
+## Project specific files
+
+SRC=  matrix.c 
+
+# MCU name
+MCU = at90usb1286
+#MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=1024
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming
+CUSTOM_MATRIX=yes # need to do our own thing with the matrix
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
+
+

keyboards/kinesis/config.h

@@ -0,0 +1,174 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    You
+#define PRODUCT         kinesis-advantage
+#define DESCRIPTION     A custom keyboard
+
+// Mouse
+#define MOUSEKEY_DELAY          20
+#define MOUSEKEY_INTERVAL       20
+#define MOUSEKEY_MAX_SPEED      4
+#define MOUSEKEY_TIME_TO_MAX    20
+#define MOUSEKEY_WHEEL_MAX_SPEED 1
+#define MOUSEKEY_WHEEL_DELTA 1
+#define MOUSEKEY_WHEEL_TIME_TO_MAX 1
+
+/* key matrix size */
+#define MATRIX_ROWS 16
+#define MATRIX_COLS  8 
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+//Passed through the port multipler, so 4 pins =16
+#define MATRIX_ROW_PINS { F0,F1, F2, F3  }
+
+// May be upside down. 
+#define MATRIX_COL_PINS { B0,B1, B2, B3, B4, B5, B6, B7 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif

keyboards/kinesis/docs/kicad/kinesis-cache.lib

@@ -0,0 +1,232 @@
+EESchema-LIBRARY Version 2.3  Date: Wednesday, November 12, 2014 'pmt' 10:15:19 pm
+#encoding utf-8
+#
+# AT90S4414-P
+#
+DEF AT90S4414-P IC 0 40 Y Y 1 F N
+F0 "IC" -850 1880 40 H V L BNN
+F1 "AT90S4414-P" 450 -1950 40 H V L BNN
+F2 "DIL40" 0 0 30 H V C CIN
+F3 "~" 0 0 60 H V C CNN
+ALIAS AT90S8515-P
+$FPLIST
+ 40DIP-ELL600
+ 40dip600
+$ENDFPLIST
+DRAW
+S -850 1850 850 -1850 0 1 10 f
+X (T0)PB0 1 1000 700 150 L 40 40 1 1 B
+X (T1)PB1 2 1000 600 150 L 40 40 1 1 B
+X (AIN0)PB2 3 1000 500 150 L 40 40 1 1 B
+X (AIN1)PB3 4 1000 400 150 L 40 40 1 1 B
+X (~SS~)PB4 5 1000 300 150 L 40 40 1 1 B
+X (MOSI)PB5 6 1000 200 150 L 40 40 1 1 B
+X (MISO)PB6 7 1000 100 150 L 40 40 1 1 B
+X (SCK)PB7 8 1000 0 150 L 40 40 1 1 B
+X ~RESET 9 -1000 1700 150 R 40 40 1 1 I
+X (RXD)PD0 10 1000 -1000 150 L 40 40 1 1 B
+X GND 20 0 -2000 150 U 40 40 1 1 W
+X ALE 30 1000 850 150 L 40 40 1 1 O
+X VCC 40 0 2000 150 D 40 40 1 1 W
+X (TXD)PD1 11 1000 -1100 150 L 40 40 1 1 B
+X (A8)PC0 21 1000 -150 150 L 40 40 1 1 B
+X ICP 31 -1000 -1400 150 R 40 40 1 1 I
+X (INT0)PD2 12 1000 -1200 150 L 40 40 1 1 B
+X (A9)PC1 22 1000 -250 150 L 40 40 1 1 B
+X (AD7)PA7 32 1000 1000 150 L 40 40 1 1 B
+X (INT1)PD3 13 1000 -1300 150 L 40 40 1 1 B
+X (A10)PC2 23 1000 -350 150 L 40 40 1 1 B
+X (AD6)PA6 33 1000 1100 150 L 40 40 1 1 B
+X PD4 14 1000 -1400 150 L 40 40 1 1 B
+X (A11)PC3 24 1000 -450 150 L 40 40 1 1 B
+X (AD5)PA5 34 1000 1200 150 L 40 40 1 1 B
+X (OC1A)PD5 15 1000 -1500 150 L 40 40 1 1 B
+X (A12)PC4 25 1000 -550 150 L 40 40 1 1 B
+X (AD4)PA4 35 1000 1300 150 L 40 40 1 1 B
+X (~WR~)PD6 16 1000 -1600 150 L 40 40 1 1 B
+X (A13)PC5 26 1000 -650 150 L 40 40 1 1 B
+X (AD3)PA3 36 1000 1400 150 L 40 40 1 1 B
+X (~RD~)PD7 17 1000 -1700 150 L 40 40 1 1 B
+X (A14)PC6 27 1000 -750 150 L 40 40 1 1 B
+X (AD2)PA2 37 1000 1500 150 L 40 40 1 1 B
+X XTAL2 18 -1000 1200 150 R 40 40 1 1 B
+X (A15)PC7 28 1000 -850 150 L 40 40 1 1 B
+X (AD1)PA1 38 1000 1600 150 L 40 40 1 1 B
+X XTAL1 19 -1000 800 150 R 40 40 1 1 B
+X OC1B 29 -1000 -1500 150 R 40 40 1 1 W
+X (AD0)PA0 39 1000 1700 150 L 40 40 1 1 B
+ENDDRAW
+ENDDEF
+#
+# ATMEGA16U4-A
+#
+DEF ATMEGA16U4-A U 0 40 Y Y 1 F N
+F0 "U" -950 1700 40 H V C CNN
+F1 "ATMEGA16U4-A" 700 -1500 40 H V C CNN
+F2 "TQFP44" 0 0 35 H V C CIN
+F3 "~" 1100 1100 60 H V C CNN
+ALIAS ATMEGA16U4RC-A ATMEGA32U4-A ATMEGA32U4RC-A
+$FPLIST
+ TQFP44
+$ENDFPLIST
+DRAW
+S -1000 1650 950 -1450 0 1 10 f
+X (INT6/AIN0)PE6 1 1100 -650 150 L 40 40 1 1 B
+X UVCC 2 -450 1800 150 D 40 40 1 1 W
+X D- 3 -1150 100 150 R 40 40 1 1 B
+X D+ 4 -1150 200 150 R 40 40 1 1 B
+X UGND 5 -400 -1600 150 U 40 40 1 1 P
+X UCAP 6 -1150 -50 150 R 40 40 1 1 P
+X VBUS 7 -1150 350 150 R 40 40 1 1 P
+X (SS/PCINT0)PB0 8 1100 1550 150 L 40 40 1 1 B
+X (SCLK/PCINT1)PB1 9 1100 1450 150 L 40 40 1 1 B
+X (PDI/MOSI/PCINT2)PB2 10 1100 1350 150 L 40 40 1 1 B
+X (RXD/INT2)PD2 20 1100 150 150 L 40 40 1 1 B
+X (ADC13/OC1B/OC4B/PCINT13)PB6 30 1100 950 150 L 40 40 1 1 B
+X (ADC1)PF1 40 1100 -950 150 L 40 40 1 1 B
+X (PDO/MISO/PCINT3)PB3 11 1100 1250 150 L 40 40 1 1 B
+X (TXD/INT3)PD3 21 1100 50 150 L 40 40 1 1 B
+X (OC3A/~OC4A~)PC6 31 1100 650 150 L 40 40 1 1 B
+X (ADC0)PF0 41 1100 -850 150 L 40 40 1 1 B
+X (OC0A/OC1C/~RTS~/PCINT7)PB7 12 1100 850 150 L 40 40 1 1 B
+X (XCK1/~CTS~)PD5 22 1100 -150 150 L 40 40 1 1 B
+X (ICP3/CLK0/OC4A)PC7 32 1100 550 150 L 40 40 1 1 B
+X AREF 42 -1150 -850 150 R 40 40 1 1 P
+X ~RESET~ 13 -1150 1550 150 R 40 40 1 1 I
+X GND 23 -50 -1600 150 U 40 40 1 1 W
+X (~HWB~)PE2 33 1100 -550 150 L 40 40 1 1 B
+X GND 43 150 -1600 150 U 40 40 1 1 W
+X VCC 14 -200 1800 150 D 40 40 1 1 W
+X AVCC 24 150 1800 150 D 40 40 1 1 W
+X VCC 34 -100 1800 150 D 40 40 1 1 W
+X AVCC 44 250 1800 150 D 40 40 1 1 W
+X GND 15 -150 -1600 150 U 40 40 1 1 W
+X (ICP2/ADC8)PD4 25 1100 -50 150 L 40 40 1 1 B
+X GND 35 50 -1600 150 U 40 40 1 1 W
+X XTAL2 16 -1150 950 150 R 40 40 1 1 O
+X (T1/~OC4D~/ADC9)PD6 26 1100 -250 150 L 40 40 1 1 B
+X (ADC7/TDI)PF7 36 1100 -1350 150 L 40 40 1 1 B
+X XTAL1 17 -1150 1150 150 R 40 40 1 1 I
+X (T0/OC4D/ADC10)PD7 27 1100 -350 150 L 40 40 1 1 B
+X (ADC6/TDO)PF6 37 1100 -1250 150 L 40 40 1 1 B
+X (OC0B/SCL/INT0)PD0 18 1100 350 150 L 40 40 1 1 B
+X (ADC11/PCINT4)PB4 28 1100 1150 150 L 40 40 1 1 B
+X (ADC5/TMS)PF5 38 1100 -1150 150 L 40 40 1 1 B
+X (SDA/INT1)PD1 19 1100 250 150 L 40 40 1 1 B
+X (ADC12/OC1A/~OC4B~/PCINT12)PB5 29 1100 1050 150 L 40 40 1 1 B
+X (ADC4/TCK)PF4 39 1100 -1050 150 L 40 40 1 1 B
+ENDDRAW
+ENDDEF
+#
+# C
+#
+DEF C C 0 10 N Y 1 F N
+F0 "C" 0 100 40 H V L CNN
+F1 "C" 6 -85 40 H V L CNN
+F2 "~" 38 -150 30 H V C CNN
+F3 "~" 0 0 60 H V C CNN
+$FPLIST
+ SM*
+ C?
+ C1-1
+$ENDFPLIST
+DRAW
+P 2 0 1 20  -80 -30  80 -30 N
+P 2 0 1 20  -80 30  80 30 N
+X ~ 1 0 200 170 D 40 40 1 1 P
+X ~ 2 0 -200 170 U 40 40 1 1 P
+ENDDRAW
+ENDDEF
+#
+# CONN_7
+#
+DEF CONN_7 P 0 40 Y N 1 F N
+F0 "P" -30 0 60 V V C CNN
+F1 "CONN_7" 70 0 60 V V C CNN
+F2 "~" 0 0 60 H V C CNN
+F3 "~" 0 0 60 H V C CNN
+DRAW
+S -100 350 150 -350 0 1 0 N
+X P1 1 -350 300 250 R 50 50 1 1 P I
+X P2 2 -350 200 250 R 50 50 1 1 P I
+X P3 3 -350 100 250 R 50 50 1 1 P I
+X P4 4 -350 0 250 R 50 50 1 1 P I
+X P5 5 -350 -100 250 R 50 50 1 1 P I
+X P6 6 -350 -200 250 R 50 50 1 1 P I
+X P7 7 -350 -300 250 R 50 50 1 1 P I
+ENDDRAW
+ENDDEF
+#
+# GND
+#
+DEF ~GND #PWR 0 0 Y Y 1 F P
+F0 "#PWR" 0 0 30 H I C CNN
+F1 "GND" 0 -70 30 H I C CNN
+F2 "~" 0 0 60 H V C CNN
+F3 "~" 0 0 60 H V C CNN
+DRAW
+P 4 0 1 0  -50 0  0 -50  50 0  -50 0 N
+X GND 1 0 0 0 U 30 30 1 1 W N
+ENDDRAW
+ENDDEF
+#
+# R
+#
+DEF R R 0 0 N Y 1 F N
+F0 "R" 80 0 40 V V C CNN
+F1 "R" 7 1 40 V V C CNN
+F2 "~" -70 0 30 V V C CNN
+F3 "~" 0 0 30 H V C CNN
+$FPLIST
+ R?
+ SM0603
+ SM0805
+ R?-*
+ SM1206
+$ENDFPLIST
+DRAW
+S -40 150 40 -150 0 1 12 N
+X ~ 1 0 250 100 D 60 60 1 1 P
+X ~ 2 0 -250 100 U 60 60 1 1 P
+ENDDRAW
+ENDDEF
+#
+# USB-MINI-B
+#
+DEF USB-MINI-B CON 0 40 Y Y 1 F N
+F0 "CON" -250 450 60 H V C CNN
+F1 "USB-MINI-B" -50 -500 60 H V C CNN
+F2 "~" 0 0 60 H V C CNN
+F3 "~" 0 0 60 H V C CNN
+$FPLIST
+ USB-Mini-B-Jack
+$ENDFPLIST
+DRAW
+S -350 400 350 -400 0 1 0 N
+X VBUS 1 -550 300 200 R 50 50 1 1 W
+X D- 2 -550 150 200 R 50 50 1 1 B
+X D+ 3 -550 0 200 R 50 50 1 1 B
+X ID 4 -550 -150 200 R 50 50 1 1 B
+X GND 5 -550 -300 200 R 50 50 1 1 W
+X SHELL1 6 550 300 200 L 50 50 1 1 B
+X SHELL2 7 550 150 200 L 50 50 1 1 B
+X SHELL3 8 550 -150 200 L 50 50 1 1 B
+X SHELL4 9 550 -300 200 L 50 50 1 1 B
+ENDDRAW
+ENDDEF
+#
+# VCC
+#
+DEF VCC #PWR 0 0 Y Y 1 F P
+F0 "#PWR" 0 100 30 H I C CNN
+F1 "VCC" 0 100 30 H V C CNN
+F2 "~" 0 0 60 H V C CNN
+F3 "~" 0 0 60 H V C CNN
+DRAW
+X VCC 1 0 0 0 U 20 20 0 0 W N
+C 0 50 20 0 1 0 N
+P 3 0 1 0  0 0  0 30  0 30 N
+ENDDRAW
+ENDDEF
+#
+#End Library

keyboards/kinesis/docs/kicad/kinesis.pro

@@ -0,0 +1,83 @@
+update=Wednesday, November 05, 2014 'pmt' 12:08:47 pm
+version=1
+last_client=pcbnew
+[cvpcb]
+version=1
+NetIExt=net
+[cvpcb/libraries]
+EquName1=devcms
+[general]
+version=1
+[eeschema]
+version=1
+PageLayoutDescrFile=
+SubpartIdSeparator=0
+SubpartFirstId=65
+LibDir=../../../lib/kicad/library
+NetFmtName=
+RptD_X=0
+RptD_Y=100
+RptLab=1
+LabSize=60
+[eeschema/libraries]
+LibName1=power
+LibName2=device
+LibName3=transistors
+LibName4=conn
+LibName5=linear
+LibName6=regul
+LibName7=74xx
+LibName8=cmos4000
+LibName9=adc-dac
+LibName10=memory
+LibName11=xilinx
+LibName12=special
+LibName13=microcontrollers
+LibName14=dsp
+LibName15=microchip
+LibName16=analog_switches
+LibName17=motorola
+LibName18=texas
+LibName19=intel
+LibName20=audio
+LibName21=interface
+LibName22=digital-audio
+LibName23=philips
+LibName24=display
+LibName25=cypress
+LibName26=siliconi
+LibName27=opto
+LibName28=atmel
+LibName29=contrib
+LibName30=valves
+LibName31=custom
+[pcbnew]
+version=1
+LastNetListRead=
+UseCmpFile=1
+PadDrill=1.016000000000
+PadDrillOvalY=1.016000000000
+PadSizeH=1.524000000000
+PadSizeV=1.524000000000
+PcbTextSizeV=1.500000000000
+PcbTextSizeH=1.500000000000
+PcbTextThickness=0.300000000000
+ModuleTextSizeV=1.000000000000
+ModuleTextSizeH=1.000000000000
+ModuleTextSizeThickness=0.150000000000
+SolderMaskClearance=0.000000000000
+SolderMaskMinWidth=0.000000000000
+DrawSegmentWidth=0.200000000000
+BoardOutlineThickness=0.100000000000
+ModuleOutlineThickness=0.150000000000
+[pcbnew/libraries]
+LibDir=../../../lib/kicad/modules
+LibName1=custom
+LibName2=Sockets
+LibName3=Connect
+LibName4=Discret
+LibName5=Divers
+LibName6=Display
+LibName7=LEDs
+LibName8=SMD_Packages
+LibName9=Sockets_DIP

keyboards/kinesis/docs/kicad/kinesis.sch

@@ -0,0 +1,634 @@
+EESchema Schematic File Version 2
+LIBS:power
+LIBS:device
+LIBS:transistors
+LIBS:conn
+LIBS:linear
+LIBS:regul
+LIBS:74xx
+LIBS:cmos4000
+LIBS:adc-dac
+LIBS:memory
+LIBS:xilinx
+LIBS:special
+LIBS:microcontrollers
+LIBS:dsp
+LIBS:microchip
+LIBS:analog_switches
+LIBS:motorola
+LIBS:texas
+LIBS:intel
+LIBS:audio
+LIBS:interface
+LIBS:digital-audio
+LIBS:philips
+LIBS:display
+LIBS:cypress
+LIBS:siliconi
+LIBS:opto
+LIBS:atmel
+LIBS:contrib
+LIBS:valves
+LIBS:custom
+LIBS:kinesis-cache
+EELAYER 27 0
+EELAYER END
+$Descr A4 11693 8268
+encoding utf-8
+Sheet 1 1
+Title ""
+Date "13 nov 2014"
+Rev ""
+Comp ""
+Comment1 ""
+Comment2 ""
+Comment3 ""
+Comment4 ""
+$EndDescr
+$Comp
+L C C4
+U 1 1 545804FB
+P 2850 4250
+F 0 "C4" H 2850 4350 40  0000 L CNN
+F 1 "1uF" H 2856 4165 40  0000 L CNN
+F 2 "~" H 2888 4100 30  0000 C CNN
+F 3 "~" H 2850 4250 60  0000 C CNN
+	1    2850 4250
+	-1   0    0    1   
+$EndComp
+$Comp
+L R R3
+U 1 1 545805E8
+P 2500 4000
+F 0 "R3" V 2580 4000 40  0000 C CNN
+F 1 "22" V 2507 4001 40  0000 C CNN
+F 2 "~" V 2430 4000 30  0000 C CNN
+F 3 "~" H 2500 4000 30  0000 C CNN
+	1    2500 4000
+	0    -1   -1   0   
+$EndComp
+$Comp
+L R R2
+U 1 1 545805FA
+P 2500 3800
+F 0 "R2" V 2580 3800 40  0000 C CNN
+F 1 "22" V 2507 3801 40  0000 C CNN
+F 2 "~" V 2430 3800 30  0000 C CNN
+F 3 "~" H 2500 3800 30  0000 C CNN
+	1    2500 3800
+	0    -1   -1   0   
+$EndComp
+Entry Wire Line
+	6450 2450 6550 2550
+Entry Wire Line
+	6450 2550 6550 2650
+Entry Wire Line
+	6450 2650 6550 2750
+Entry Wire Line
+	6450 2750 6550 2850
+Entry Wire Line
+	6450 2950 6550 3050
+Entry Wire Line
+	6450 3050 6550 3150
+Entry Wire Line
+	6450 2850 6550 2950
+Entry Wire Line
+	6450 3150 6550 3250
+Wire Wire Line
+	10250 1800 10750 1800
+Entry Wire Line
+	10750 1800 10850 1900
+Entry Wire Line
+	10750 1900 10850 2000
+Entry Wire Line
+	10750 2000 10850 2100
+Entry Wire Line
+	10750 2800 10850 2900
+Entry Wire Line
+	10750 2900 10850 3000
+Entry Wire Line
+	10750 3000 10850 3100
+Entry Wire Line
+	10750 3100 10850 3200
+Entry Wire Line
+	10750 3200 10850 3300
+Entry Wire Line
+	10750 3300 10850 3400
+$Comp
+L AT90S8515-P IC2
+U 1 1 545A62EA
+P 9250 3500
+F 0 "IC2" H 8400 5380 40  0000 L BNN
+F 1 "AT90S8515-P" H 9700 1550 40  0000 L BNN
+F 2 "DIL40" H 9250 3500 30  0000 C CIN
+F 3 "" H 9250 3500 60  0000 C CNN
+	1    9250 3500
+	1    0    0    -1  
+$EndComp
+NoConn ~ 10250 2650
+Entry Wire Line
+	10750 3650 10850 3750
+Entry Wire Line
+	10750 3750 10850 3850
+Entry Wire Line
+	10750 3850 10850 3950
+Entry Wire Line
+	10750 3950 10850 4050
+Entry Wire Line
+	10750 4050 10850 4150
+Entry Wire Line
+	10750 4150 10850 4250
+Entry Wire Line
+	10750 4350 10850 4450
+Entry Wire Line
+	10750 4250 10850 4350
+NoConn ~ 8250 4900
+NoConn ~ 8250 5000
+NoConn ~ 8250 1800
+Wire Wire Line
+	10250 1900 10750 1900
+Wire Wire Line
+	10250 2000 10750 2000
+Wire Wire Line
+	10250 2100 10750 2100
+Wire Wire Line
+	10250 2200 10750 2200
+Wire Wire Line
+	10250 2300 10750 2300
+Wire Wire Line
+	10250 2400 10750 2400
+Wire Wire Line
+	10250 2500 10750 2500
+Text Label 10350 1800 0    60   ~ 0
+A
+Text Label 10350 1900 0    60   ~ 0
+B
+Text Label 10350 2000 0    60   ~ 0
+C
+Text Label 10350 2100 0    60   ~ 0
+G
+Wire Wire Line
+	10250 2800 10750 2800
+Wire Wire Line
+	10250 2900 10750 2900
+Wire Wire Line
+	10250 3000 10750 3000
+Wire Wire Line
+	10250 3100 10750 3100
+Wire Wire Line
+	10250 3200 10750 3200
+Wire Wire Line
+	10250 3300 10750 3300
+Wire Wire Line
+	10250 3400 10750 3400
+Wire Wire Line
+	10250 3500 10750 3500
+Text Label 10350 2800 0    60   ~ 0
+DL2
+Text Label 10350 2900 0    60   ~ 0
+DR1
+Text Label 10350 3000 0    60   ~ 0
+DR2
+Text Label 10350 3100 0    60   ~ 0
+DL1
+Text Label 10350 3400 0    60   ~ 0
+SCL
+Text Label 10350 3500 0    60   ~ 0
+SDA
+Wire Wire Line
+	10250 3650 10750 3650
+Wire Wire Line
+	10250 3750 10750 3750
+Wire Wire Line
+	10250 3850 10750 3850
+Wire Wire Line
+	10250 3950 10750 3950
+Wire Wire Line
+	10250 4050 10750 4050
+Wire Wire Line
+	10250 4150 10750 4150
+Wire Wire Line
+	10250 4250 10750 4250
+Wire Wire Line
+	10250 4350 10750 4350
+Text Label 10350 3650 0    60   ~ 0
+R1
+Text Label 10350 3750 0    60   ~ 0
+R2
+Text Label 10350 3850 0    60   ~ 0
+R3
+Text Label 10350 3950 0    60   ~ 0
+R4
+Text Label 10350 4050 0    60   ~ 0
+R5
+Text Label 10350 4150 0    60   ~ 0
+R6
+Text Label 10350 4250 0    60   ~ 0
+R7
+Text Label 10350 4350 0    60   ~ 0
+R8
+Wire Wire Line
+	10250 4500 10750 4500
+Wire Wire Line
+	10250 4600 10750 4600
+Wire Wire Line
+	10250 4700 10750 4700
+Wire Wire Line
+	10250 4800 10750 4800
+Wire Wire Line
+	10250 4900 10750 4900
+Wire Wire Line
+	10250 5000 10750 5000
+Wire Wire Line
+	10250 5100 10750 5100
+Wire Wire Line
+	10250 5200 10750 5200
+Text Label 10350 4600 0    60   ~ 0
+FS1
+Text Label 10350 5000 0    60   ~ 0
+FS3
+Text Label 10350 5200 0    60   ~ 0
+FS2
+$Comp
+L GND #PWR01
+U 1 1 545A7377
+P 9250 5600
+F 0 "#PWR01" H 9250 5600 30  0001 C CNN
+F 1 "GND" H 9250 5530 30  0001 C CNN
+F 2 "" H 9250 5600 60  0000 C CNN
+F 3 "" H 9250 5600 60  0000 C CNN
+	1    9250 5600
+	1    0    0    -1  
+$EndComp
+Wire Wire Line
+	9250 5500 9250 5600
+Text Label 10350 4700 0    60   ~ 0
+CLOCK
+Text Label 10350 4800 0    60   ~ 0
+DATA
+NoConn ~ 10750 4700
+NoConn ~ 10750 4800
+Text Label 10350 3200 0    60   ~ 0
+KP
+Text Label 10350 3300 0    60   ~ 0
+PGM
+Text Label 10350 2500 0    60   ~ 0
+BUZZ
+NoConn ~ 8250 2300
+NoConn ~ 8250 2700
+$Comp
+L GND #PWR02
+U 1 1 545A7565
+P 4750 5700
+F 0 "#PWR02" H 4750 5700 30  0001 C CNN
+F 1 "GND" H 4750 5630 30  0001 C CNN
+F 2 "" H 4750 5700 60  0000 C CNN
+F 3 "" H 4750 5700 60  0000 C CNN
+	1    4750 5700
+	1    0    0    -1  
+$EndComp
+Entry Wire Line
+	6450 3650 6550 3750
+Entry Wire Line
+	6450 3750 6550 3850
+Entry Wire Line
+	6450 4150 6550 4250
+Entry Wire Line
+	6450 4250 6550 4350
+Entry Wire Line
+	6450 4050 6550 4150
+Entry Wire Line
+	6450 4350 6550 4450
+NoConn ~ 3750 2850
+Wire Wire Line
+	1200 2000 6450 2000
+NoConn ~ 3750 3050
+Wire Wire Line
+	2750 3800 3750 3800
+Wire Wire Line
+	2750 3900 3750 3900
+Wire Wire Line
+	2750 3900 2750 4000
+Wire Bus Line
+	6550 2100 6550 6050
+Wire Bus Line
+	10850 1600 10850 6050
+Text Label 6050 4350 0    60   ~ 0
+DL1
+Text Label 6050 4250 0    60   ~ 0
+DR2
+Text Label 6050 4150 0    60   ~ 0
+DR1
+Text Label 6050 4050 0    60   ~ 0
+DL2
+Text Label 6050 2450 0    60   ~ 0
+R1
+Text Label 6050 2550 0    60   ~ 0
+R2
+Text Label 6050 2650 0    60   ~ 0
+R3
+Text Label 6050 2750 0    60   ~ 0
+R4
+Text Label 6050 2850 0    60   ~ 0
+R5
+Text Label 6050 2950 0    60   ~ 0
+R6
+Text Label 6050 3050 0    60   ~ 0
+R7
+Text Label 6050 3150 0    60   ~ 0
+R8
+Text Label 6050 5050 0    60   ~ 0
+A
+Text Label 6050 5150 0    60   ~ 0
+B
+Text Label 6050 5250 0    60   ~ 0
+C
+Text Label 6050 5350 0    60   ~ 0
+G
+Text Label 1300 3800 0    60   ~ 0
+D+
+Text Label 1300 4000 0    60   ~ 0
+D-
+NoConn ~ 10750 2200
+NoConn ~ 10750 2300
+NoConn ~ 10750 2400
+Text Label 10350 4500 0    60   ~ 0
+GND
+NoConn ~ 10750 4900
+NoConn ~ 10750 5100
+Text Label 6050 3450 0    60   ~ 0
+KP
+Text Label 6050 3350 0    60   ~ 0
+PGM
+$Comp
+L ATMEGA32U4-A U1
+U 1 1 5462E0B1
+P 4900 4000
+F 0 "U1" H 3950 5700 40  0000 C CNN
+F 1 "ATMEGA32U4-A" H 5600 2500 40  0000 C CNN
+F 2 "TQFP44" H 4900 4000 35  0000 C CIN
+F 3 "" H 6000 5100 60  0000 C CNN
+	1    4900 4000
+	1    0    0    -1  
+$EndComp
+Wire Wire Line
+	3750 4850 3750 5600
+Wire Wire Line
+	4450 2200 5150 2200
+Connection ~ 4700 2200
+Connection ~ 4800 2200
+Connection ~ 5050 2200
+Connection ~ 4800 2000
+Wire Wire Line
+	6000 2450 6450 2450
+Wire Wire Line
+	6000 2550 6450 2550
+Wire Wire Line
+	6000 2650 6450 2650
+Wire Wire Line
+	6000 2750 6450 2750
+Wire Wire Line
+	6000 2850 6450 2850
+Wire Wire Line
+	6000 2950 6450 2950
+Wire Wire Line
+	6000 3050 6450 3050
+Wire Wire Line
+	6000 3150 6450 3150
+Wire Wire Line
+	6000 5050 6450 5050
+Wire Wire Line
+	6000 5150 6450 5150
+Wire Wire Line
+	6000 5250 6450 5250
+Wire Wire Line
+	6000 4050 6450 4050
+Wire Wire Line
+	6000 4150 6450 4150
+Wire Wire Line
+	6000 4250 6450 4250
+Wire Wire Line
+	6000 4350 6450 4350
+Wire Wire Line
+	6000 4550 6450 4550
+Entry Wire Line
+	6450 3350 6550 3450
+Entry Wire Line
+	6450 3450 6550 3550
+Entry Wire Line
+	6450 5050 6550 5150
+Entry Wire Line
+	6450 5150 6550 5250
+Entry Wire Line
+	6450 5250 6550 5350
+Entry Wire Line
+	6450 5350 6550 5450
+Entry Wire Line
+	6450 4650 6550 4750
+Wire Wire Line
+	6000 3350 6450 3350
+Wire Wire Line
+	6000 3450 6450 3450
+Wire Wire Line
+	1200 5600 6450 5600
+Connection ~ 4950 5600
+Connection ~ 4850 5600
+Wire Wire Line
+	4750 5600 4750 5700
+Connection ~ 4750 5600
+Connection ~ 4500 5600
+Text Label 6050 4550 0    60   ~ 0
+HWB
+Wire Wire Line
+	6000 5350 6450 5350
+Wire Wire Line
+	6000 3650 6450 3650
+Wire Wire Line
+	6000 3750 6450 3750
+Text Label 6050 3650 0    60   ~ 0
+SCL
+Text Label 6050 3750 0    60   ~ 0
+SDA
+Wire Wire Line
+	6000 3850 6450 3850
+Wire Wire Line
+	6000 3950 6450 3950
+Wire Wire Line
+	6000 4650 6450 4650
+Text Label 6050 4650 0    60   ~ 0
+BUZZ
+NoConn ~ 10750 4600
+NoConn ~ 10750 5000
+NoConn ~ 10750 5200
+Entry Wire Line
+	10750 3400 10850 3500
+Entry Wire Line
+	10750 3500 10850 3600
+Entry Wire Line
+	10750 4500 10850 4600
+Wire Wire Line
+	2850 4050 3750 4050
+Text Label 2950 4050 0    60   ~ 0
+UCAP
+Wire Wire Line
+	6000 4850 6450 4850
+Wire Wire Line
+	6000 4950 6450 4950
+NoConn ~ 6450 4850
+NoConn ~ 6450 4950
+NoConn ~ 6450 4550
+$Comp
+L USB-MINI-B CON1
+U 1 1 546431C1
+P 2100 5050
+F 0 "CON1" H 1850 5500 60  0000 C CNN
+F 1 "USB-MINI-B" H 2050 4550 60  0000 C CNN
+F 2 "" H 2100 5050 60  0000 C CNN
+F 3 "" H 2100 5050 60  0000 C CNN
+	1    2100 5050
+	0    1    1    0   
+$EndComp
+$Comp
+L VCC #PWR03
+U 1 1 54643698
+P 2400 4400
+F 0 "#PWR03" H 2400 4500 30  0001 C CNN
+F 1 "VCC" H 2400 4500 30  0000 C CNN
+F 2 "" H 2400 4400 60  0000 C CNN
+F 3 "" H 2400 4400 60  0000 C CNN
+	1    2400 4400
+	1    0    0    -1  
+$EndComp
+Text Notes 2600 2750 0    60   ~ 0
+Teensy 2.0\n(not fully drawn)
+$Comp
+L CONN_7 B7K-PH-K-S1
+U 1 1 54643939
+P 1950 6900
+F 0 "B7K-PH-K-S1" V 1920 6900 60  0000 C CNN
+F 1 "CONN_7" V 2020 6900 60  0000 C CNN
+F 2 "" H 1950 6900 60  0000 C CNN
+F 3 "" H 1950 6900 60  0000 C CNN
+	1    1950 6900
+	1    0    0    -1  
+$EndComp
+Connection ~ 3750 5600
+Connection ~ 2400 5600
+Connection ~ 2250 5600
+Connection ~ 1950 5600
+Wire Wire Line
+	2400 4400 2400 4500
+Wire Wire Line
+	2250 4000 2250 4500
+Wire Wire Line
+	1200 3800 2250 3800
+Wire Wire Line
+	2100 3800 2100 4500
+Wire Wire Line
+	2850 4450 2850 5600
+Connection ~ 2850 5600
+Entry Wire Line
+	1100 6800 1200 6900
+Entry Wire Line
+	1100 6900 1200 7000
+Entry Wire Line
+	1100 7000 1200 7100
+Entry Wire Line
+	1100 6700 1200 6800
+Wire Wire Line
+	1200 6600 1600 6600
+Wire Wire Line
+	1200 6700 1600 6700
+Wire Wire Line
+	1200 6800 1600 6800
+Wire Wire Line
+	1200 6900 1600 6900
+Wire Wire Line
+	1200 7000 1600 7000
+Wire Wire Line
+	1200 7100 1600 7100
+Wire Wire Line
+	1200 7200 1600 7200
+Text Label 1300 6600 0    60   ~ 0
+FS2
+Text Label 1300 6700 0    60   ~ 0
+FS1
+Text Label 1300 6800 0    60   ~ 0
+VCC
+Text Label 1300 6900 0    60   ~ 0
+D-
+Text Label 1300 7000 0    60   ~ 0
+D+
+Text Label 1300 7100 0    60   ~ 0
+GND
+Text Label 1300 7200 0    60   ~ 0
+FS3
+NoConn ~ 3750 2450
+Wire Wire Line
+	3600 2000 3600 3650
+Wire Wire Line
+	3600 3650 3750 3650
+NoConn ~ 1950 4500
+Wire Bus Line
+	1100 1900 1100 7100
+NoConn ~ 1200 6600
+NoConn ~ 1200 6700
+NoConn ~ 1200 7200
+Connection ~ 2100 3800
+Wire Wire Line
+	1200 4000 2250 4000
+Entry Wire Line
+	1100 3700 1200 3800
+Entry Wire Line
+	1100 3900 1200 4000
+Text Label 10350 1500 0    60   ~ 0
+VCC
+Entry Wire Line
+	1100 1900 1200 2000
+Text Label 1250 2000 0    60   ~ 0
+VCC
+Entry Wire Line
+	1100 5500 1200 5600
+Connection ~ 1800 5600
+Text Label 1300 5600 0    60   ~ 0
+GND
+Wire Wire Line
+	9250 5500 10750 5500
+Entry Wire Line
+	10750 5500 10850 5600
+Text Label 10350 5500 0    60   ~ 0
+GND
+Wire Wire Line
+	9250 1500 10750 1500
+Entry Wire Line
+	10750 1500 10850 1600
+Connection ~ 3600 2000
+Wire Wire Line
+	4800 2000 4800 2200
+Entry Wire Line
+	6450 2000 6550 2100
+Text Label 6050 2000 0    60   ~ 0
+VCC
+Connection ~ 5050 5600
+Entry Wire Line
+	6450 5600 6550 5700
+Text Label 6050 5600 0    60   ~ 0
+GND
+NoConn ~ 6450 3850
+NoConn ~ 6450 3950
+Wire Wire Line
+	1800 4500 1500 4500
+Wire Wire Line
+	1500 4500 1500 5600
+Connection ~ 1500 5600
+Entry Wire Line
+	10750 2500 10850 2600
+Entry Wire Line
+	10750 2100 10850 2200
+Text Notes 1000 5300 1    60   ~ 0
+Sacrificial USB cable from header to Teensy
+Text Notes 7850 5950 0    60   ~ 0
+Ribbon cable between Teensy pins and socket
+Wire Bus Line
+	10850 6050 6550 6050
+$EndSCHEMATC

keyboards/kinesis/docs/readme.txt

@@ -0,0 +1,52 @@
+This directory of documentation  was copied from https://github.com/wjanssens/tmk_keyboard/tree/master/keyboard/kinesis
+and is probably Copyright 2014 Warren Janssens <warren.janssens@gmail.com>
+and probably released under GPL v2, which may be recovered at <http://www.gnu.org/licenses/>.
+
+Row configuration
+PF0	A
+PF1	B
+PF2	C
+PF3	G	0 = U4, 1 = U5
+
+Column configuration
+			4y0	4y1	4y2	4y3	4y4	4y5	4y6	4y7	5y0	5y1	5y2	5y3	5y4	5y5	5y6	5y7	
+			r1	r2	 r3 r4	r5	r6	r7	r8	r9	r10	r11	r12	r13	r14	r15	r16	
+PB0	21	c1	f6	f8	f7	5	4	3	2	1	=+								
+PB1	22	c2	f3	f5	f4	t	r	e	w	q	TAB								
+PB2	23	c3	ESC	f2	f1	g	f	d	s	a	CL								
+PB3	24	c4	f9	f11	f10	b	v	c	x	z	LS	UP		DN		[{	]}		
+PB4	25	c5  	f12	SL	PS	RT		LT	§±	`~		6	7	8		9	0	-_ 	
+PB5	26	c6	PB	PGM	KPD							y	u	i		o	p	\	
+PB6	27	c7  			LC	DL	BS	RC	EN	SP	h	j	k		l	;:	'"	
+PB7	28	c8					RA		PU		PD	n	m	,<		.>	/?	RS	
+ */
+
+
+40 pin connector
+
+   DL2	1	40	VCC
+   DR1	2	39	A
+   DR2	3	38	B
+   DL1	4	37	C
+   KPD	5	36	G
+   PGM	6	35
+   SCL	7	34
+   SDA	8	33
+   RST	9	32	BUZZ
+    WP	10	31	EA
+   FS1	11	30	ALE
+ CLOCK	12	29	PSEN
+  DATA	13	28	r8
+	14	27	r7
+   FS3	15	26	r6
+	16	25	r5
+   FS2	17	24	r4
+ XTAL1	18	23	r3
+ XTAL2	19	22	r2
+   GND	20	21	r1
+
+
+references:
+https://github.com/chrisandreae/keyboard-firmware
+
+

keyboards/kinesis/keymaps/default/Makefile

@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif

keyboards/kinesis/keymaps/default/config.h

@@ -0,0 +1,8 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif

keyboards/kinesis/keymaps/default/keymap.c

@@ -0,0 +1,116 @@
+#include "kinesis.h"
+#include "action_layer.h"
+
+#define QWERTY 0 // Base qerty
+#define SYMB 1// Symbol layer
+
+// An almost entirely blank keymap. Test layers with the upper right hand key - 1 in normal mode, reset in layer 2. 
+
+
+/****************************************************************************************************
+*
+* Keymap: Default Layer in Qwerty
+*
+* ,-------------------------------------------------------------------------------------------------------------------.
+* | Esc    |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |  F8  |  F9  |  F10 |  F12 | PSCR | SLCK | PAUS |  FN0 |  BOOT  |
+* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------|
+* | =+     |  1!  |  2@  |  3#  |  4$  |  5%  |                           |  6^  |  7&  |  8*  |  9(  |  0)  | -_     |
+* |--------+------+------+------+------+------|                           +------+------+------+------+------+--------|
+* | Tab    |   Q  |   W  |   E  |   R  |   T  |                           |   Y  |   U  |   I  |   O  |   P  | \|     |
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* | Caps   |   A  |   S  |   D  |   F  |   G  |                           |   H  |   J  |   K  |   L  |  ;:  | '"     |
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* | Shift  |   Z  |   X  |   C  |   V  |   B  |                           |   N  |   M  |  ,.  |  .>  |  /?  | Shift  |
+* `--------+------+------+------+------+-------                           `------+------+------+------+------+--------'
+*          | `~   | INS  | Left | Right|                                         | Up   | Down |  [{  |  ]}  |
+*          `---------------------------'                                         `---------------------------'
+*                                        ,-------------.         ,-------------.
+*                                        | Ctrl | Alt  |         | Gui  | Ctrl |
+*                                 ,------|------|------|         |------+------+------.
+*                                 |      |      | Home |         | PgUp |      |      |
+*                                 | BkSp | Del  |------|         |------|Return| Space|
+*                                 |      |      | End  |         | PgDn |      |      |
+*                                 `--------------------'         `--------------------'
+*/
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[QWERTY] = KEYMAP(
+           KC_ESC, KC_F1  ,KC_F2  ,KC_F3  ,KC_F4  ,KC_F5  ,KC_F6  ,KC_F7  ,KC_F8,
+           KC_EQL, KC_1   ,KC_2   ,KC_3   ,KC_4   ,KC_5   ,
+           KC_TAB, KC_Q   ,KC_W   ,KC_E   ,KC_R   ,KC_T   ,
+           KC_CAPS,KC_A   ,KC_S   ,KC_D   ,KC_F   ,KC_G   ,
+           KC_LSFT,KC_Z   ,KC_X   ,KC_C   ,KC_V   ,KC_B   ,
+                   KC_GRV ,KC_INS ,KC_LEFT,KC_RGHT,
+			   KC_LCTL,KC_LALT,
+                                    KC_HOME,
+                           KC_BSPC,KC_DEL ,KC_END ,
+        KC_F9  ,KC_F10 ,KC_F11 ,KC_F12 ,KC_PSCR ,KC_SLCK  ,KC_PAUS, KC_FN0, KC_1,
+	KC_6   ,KC_7   ,KC_8   ,KC_9   ,KC_0   ,KC_MINS,
+	KC_Y   ,KC_U   ,KC_I   ,KC_O   ,KC_P   ,KC_BSLS,
+	KC_H   ,KC_J   ,KC_K   ,KC_L   ,KC_SCLN,KC_QUOT,
+	KC_N   ,KC_M   ,KC_COMM,KC_DOT ,KC_SLSH,KC_RSFT,
+		KC_UP  ,KC_DOWN,KC_LBRC,KC_RBRC,
+           KC_RGUI,KC_RCTL,
+           KC_PGUP,
+           KC_PGDN,KC_ENTER ,KC_SPC
+    ),
+[SYMB] = KEYMAP( 
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 	   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	                     KC_TRNS,  KC_TRNS,
+				       KC_TRNS,
+		    KC_TRNS, KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_FN0, RESET,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 	   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+	 KC_TRNS,  KC_TRNS,
+	 KC_TRNS,
+	 KC_TRNS,  KC_TRNS,  KC_TRNS
+    )
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+   [0] = ACTION_LAYER_TAP_TOGGLE(SYMB) ,               // FN1 - Momentary Layer 1 (Symbols)
+
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+      }
+    return MACRO_NONE;
+};
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/kinesis/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for kinesis-advantage

keyboards/kinesis/keymaps/programmer/Makefile

@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif

keyboards/kinesis/keymaps/programmer/config.h

@@ -0,0 +1,8 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif

keyboards/kinesis/keymaps/programmer/keymap.c

@@ -0,0 +1,245 @@
+#include "kinesis.h"
+#include "action_layer.h"
+#include "mousekey.h"
+
+#define QWERTY 0 // Base qerty
+#define SYMB 1// Symbol layer
+#define MOUSE 2//
+
+
+
+
+/* Macros */
+enum {
+  NONE = 0,
+  // Diagonal mouse movement
+  A_MUL,
+  A_MUR,
+  A_MDL,
+  A_MDR,
+};
+
+
+// Borrowing very heavily from 
+// https://github.com/alvicstep/tmk_keyboard 
+/****************************************************************************************************
+*
+* Keymap: Default Layer in Qwerty
+*
+* ,-------------------------------------------------------------------------------------------------------------------.
+* | Esc    |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |  F8  |  F9  |  F10 |  F12 |  FN0 |  FN1 |  FN2 |      |  bOOT  |
+* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------|
+* | =+     |  1!  |  2@  |  3#  |  4$  |  5%  |                           |  6^  |  7&  |  8*  |  9(  |  0)  | -_     |
+* |--------+------+------+------+------+------|                           +------+------+------+------+------+--------|
+* | Tab    |   Q  |   W  |   E  |   R  |   T  |                           |   Y  |   U  |   I  |   O  |   P  | \|     |
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* |MouseFN1|   A  |   S  |   D  |   F  |   G  |                           |   H  |   J  |   K  |   L  |  ;:  | '"     |
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* | Shift  |   Z  |   X  |   C  |   V  |   B  |                           |   N  |   M  |  ,.  |  .>  |  /?  | Shift  |
+* `--------+------+------+------+------+-------                           `------+------+------+------+------+--------'
+*          | `~   | ESC  |MOUSE1|MOUSE2|                                         | [{   |  ]}  | ESC  | GUI  |
+*          `---------------------------'                                         `---------------------------'
+*                                        ,-------------.         ,-------------.
+*                                        | Ctrl | Alt  |         | Gui  | Ctrl |
+*                                 ,------|------|------|         |------+------+------.
+*                                 |      |      | Home |         | PgUp |      |      |
+*                                 | BkSp | Del  |------|         |------|Return| Space|
+*                                 |      |      | End  |         | PgDn |      |      |
+*                                 `--------------------'         `--------------------'
+*/
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[QWERTY] = KEYMAP(
+           KC_ESC, KC_F1  ,KC_F2  ,KC_F3  ,KC_F4  ,KC_F5  ,KC_F6  ,KC_F7  ,KC_F8,
+           KC_EQL, KC_1   ,KC_2   ,KC_3   ,KC_4   ,KC_5   ,
+           KC_TAB, KC_Q   ,KC_W   ,KC_E   ,KC_R   ,KC_T   ,
+           KC_FN1 ,KC_A   ,KC_S   ,KC_D   ,KC_F   ,KC_G   ,
+           KC_LSFT,KC_Z   ,KC_X   ,KC_C   ,KC_V   ,KC_B   ,
+		KC_GRV  ,KC_ESC,  KC_BTN1,KC_BTN2,
+			   KC_LCTL,KC_LALT,
+			   KC_HOME,
+                           KC_BSPC,KC_DEL ,KC_FN0 ,
+        KC_F9  ,KC_F10 ,KC_F11 ,KC_F12 ,KC_FN0 ,KC_FN1  ,KC_FN2, KC_NO, RESET,
+	KC_6   ,KC_7   ,KC_8   ,KC_9   ,KC_0   ,KC_MINS,
+	KC_Y   ,KC_U   ,KC_I   ,KC_O   ,KC_P   ,KC_BSLS,
+	KC_H   ,KC_J   ,KC_K   ,KC_L   ,KC_SCLN,KC_QUOT,
+	KC_N   ,KC_M   ,KC_COMM,KC_DOT ,KC_SLSH,KC_RSFT,
+		KC_LBRC,KC_RBRC, KC_ESC, KC_RGUI,
+           KC_RGUI,KC_RCTL,
+           KC_PGUP,
+           KC_PGDN,KC_ENTER ,KC_SPC
+    ),
+[SYMB] = KEYMAP( 
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+                   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+                             KC_TRNS,  KC_TRNS,
+                                       KC_TRNS,
+                    KC_TRNS, KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_FN0, KC_2,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+                   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,
+         KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS
+    ),
+/* Keymap: Movement and function layer
+*
+* ,-------------------------------------------------------------------------------------------------------------------.
+* | Caps   |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |  F8  |  F9  |  F10 |  F12 |  FN0 |  FN1 |  FN2 |  Tada |  bOOT  |
+* |--------+------+------+------+------+------+---------------------------+------+------+------+------+------+--------|
+* | =+     |  !   |   @  |   #  |   $  |   %  |                           |  ^   |   &  |   *  |  (   |   )  |MS Fast |
+* |--------+------+------+------+------+------|                           +------+------+------+------+------+--------|
+* | Tab    |      |      | Up   |      |PgUp  |                           | MwU  |MS_UL | MS_U |MS_UR |      | Ms Norm| 
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* |MouseFN1| C^A  | Left | Down |Right | C^E  |                           |      | MS_L |Mouse1| MS_R |      |MS Slow |
+* |--------+------+------+------+------+------|                           |------+------+------+------+------+--------|
+* |        | GuiZ | GUI X| GUI C| GUI_V|PgDown|                           | MWD  | MDown|MS Dwn|MS_DR  |  ?  |        |
+* `--------+------+------+------+------+-------                           `------+------+------+------+------+--------'
+*          | `~   | ESC  |   <  |   >  |                                         |  {   |   }  | ESC  |      |
+*          `---------------------------'                                         `---------------------------'
+*                                        ,-------------.         ,-------------.
+*                                        | Ctrl | Alt  |         | Gui  | Ctrl |
+*                                 ,------|------|------|         |------+------+------.
+*                                 |      |      | Home |         | PgUp |      |      |
+*                                 | BkSp | Del  |------|         |------|Mouse1|Mouse2|
+*                                 |      |      | End  |         | PgDn |LClick|Rclick|
+*                                 `--------------------'         `--------------------'
+*/
+
+
+[MOUSE] = KEYMAP(
+         KC_CAPS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+         KC_TRNS,  KC_EXLM  ,KC_AT,    KC_HASH,  KC_DLR   ,KC_PERC   ,
+         KC_TRNS,  KC_NO,    KC_NO,    KC_UP,    KC_NO,    KC_PGUP,
+         KC_FN1,  LCTL(KC_A),KC_LEFT,  KC_DOWN,  KC_RIGHT, LCTL(KC_E),
+         KC_TRNS, LGUI(KC_Z),LGUI(KC_X),LGUI(KC_C),LGUI(KC_V),KC_PGDN,
+                   KC_TRNS,  KC_TRNS,  KC_LABK,  KC_RABK,
+                             KC_TRNS,  KC_TRNS,
+                                       KC_TRNS,
+                    KC_TRNS, KC_TRNS,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS, KC_FN0,RESET, 
+         KC_CIRC,  KC_AMPR,  KC_ASTR,  KC_LPRN,  KC_RPRN,  KC_ACL2,  
+         KC_WH_U,  M(A_MUL), KC_MS_U,  M(A_MUR), KC_NO,  KC_ACL1,
+         KC_NO,    KC_MS_L,  KC_MS_D,  KC_MS_R,  KC_NO,  KC_ACL0,
+         KC_WH_D,  M(A_MDL), KC_MS_D,  M(A_MDR), KC_TRNS, KC_TRNS,
+                   KC_LCBR,  KC_RCBR,  KC_ESC,  KC_TRNS,
+         KC_TRNS,  KC_TRNS,
+         KC_TRNS,
+         KC_TRNS,  KC_BTN1,  KC_BTN2
+    ),
+
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+   [0] = ACTION_LAYER_TAP_TOGGLE(MOUSE) ,               // FN1 - Momentary Layer 1 (Symbols)
+   [1] = ACTION_LAYER_TOGGLE(MOUSE) ,               // FN1 - Momentary Layer 1 (Symbols)
+   [2] = ACTION_LAYER_TAP_TOGGLE(SYMB) ,               // FN1 - Momentary Layer 1 (Symbols)
+
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+
+	// from  algernon's ErgoDox EZ layout, 
+       case A_MUL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case A_MUR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+
+      case A_MDL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case A_MDR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+     } 
+    return MACRO_NONE;
+};
+
+
+void matrix_init_user(void) {
+
+
+}
+
+void matrix_scan_user(void) {
+ int8_t layer = biton32(layer_state);
+
+        switch (layer) {
+        case 1:
+                all_led_off();
+                break;
+        case 2:
+                if (!(host_keyboard_leds() & (1 << USB_LED_CAPS_LOCK))) {
+                        all_led_off();
+                        caps_lock_led_on();
+                }
+                break;
+        case 0:
+                all_led_off();
+                num_lock_led_on();
+                break;
+        default:
+                break;
+        }
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/kinesis/keymaps/programmer/readme.md

@@ -0,0 +1,2 @@
+# a programmer friendly keymap for the kinesis-advantage
+# not really baked yet. 

keyboards/kinesis/kinesis.c

@@ -0,0 +1,106 @@
+#include "kinesis.h"
+
+// begin section origin  https://github.com/alvicstep/tmk_keyboard 
+
+
+void all_led_off(void)
+{
+        PORTD = 0b11111111;
+}
+
+void all_led_on(void)
+{
+        PORTD = 0b00000000;
+}
+void num_lock_led_on(void)
+{
+        PORTD = 0b11101111;
+}
+
+void caps_lock_led_on(void)
+{
+        PORTD = 0b01111111;
+}
+
+void scroll_lock_led_on(void)
+{
+        PORTD = 0b11011111;
+}
+void keypad_led_on(void)
+{
+        PORTD = 0b10111111;
+}
+void blink_all_leds(void)
+{
+        all_led_on();
+        _delay_ms(500);
+
+        all_led_off();
+        _delay_ms(100);
+
+        caps_lock_led_on();
+        _delay_ms(100);
+
+	 num_lock_led_on();
+        _delay_ms(100);
+
+        scroll_lock_led_on();
+        _delay_ms(100);
+
+         keypad_led_on();
+        _delay_ms(100);
+
+        //back
+
+        scroll_lock_led_on();
+        _delay_ms(100);
+
+        num_lock_led_on();
+        _delay_ms(100);
+
+        caps_lock_led_on();
+        _delay_ms(100);
+
+        all_led_off();
+}
+
+// End section origin  https://github.com/alvicstep/tmk_keyboard 
+
+ void matrix_init_kb(void) {
+	  blink_all_leds();
+	  matrix_init_user();
+}
+
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+	
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+//Copyright 2014 Warren Janssens <warren.janssens@gmail.com>
+   uint8_t leds = 0xF0;
+    if (usb_led & 1 << USB_LED_NUM_LOCK)
+        leds &= ~0x10;
+    if (usb_led & 1 << USB_LED_CAPS_LOCK)
+        leds &= ~0x80;
+    if (usb_led & 1 << USB_LED_SCROLL_LOCK)
+        leds &= ~0x20;
+    PORTD = (PORTD & 0x0F) | leds;
+
+	led_set_user(usb_led);
+
+}
+
+

keyboards/kinesis/kinesis.h

@@ -0,0 +1,67 @@
+#ifndef KINESIS_H
+#define KINESIS_H
+
+#include "quantum.h"
+
+
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+
+#define KEYMAP(                           \
+    k02,k22,k12,k01,k21,k11,k00,k20,k10,  \
+    k80,k70,k60,k50,k40,k30,              \
+    k81,k71,k61,k51,k41,k31,              \
+    k82,k72,k62,k52,k42,k32,              \
+    k83,k73,k63,k53,k43,k33,              \
+        k74,k64,k54,k34,                  \
+                        k36,k35,          \
+                            k55,          \
+                    k56,k46,k75,          \
+    k03,k23,k13,k04,k24,k14,k05,k85,k84,  \
+        k94,kA4,kB4,kD4,kE4,kF4,          \
+        k95,kA5,kB5,kD5,kE5,kF5,          \
+        k96,kA6,kB6,kD6,kE6,kF6,          \
+        k97,kA7,kB7,kD7,kE7,kF7,          \
+            k93,kB3,kD3,kE3,              \
+    k47,k66,                              \
+    k67,                                  \
+    k87,k76,k86                           \
+) {                                       \
+        { k00,    k01,    k02,    k03,    k04,    k05,    KC_NO,   KC_NO   }, \
+        { k10,    k11,    k12,    k13,    k14,    KC_NO,  KC_NO,   KC_NO   }, \
+        { k20,    k21,    k22,    k23,    k24,    KC_NO,  KC_NO,   KC_NO   }, \
+        { k30,    k31,    k32,    k33,    k34,    k35,    k36,     KC_NO   }, \
+        { k40,    k41,    k42,    k43,    KC_NO,  KC_NO,  k46,     k47     }, \
+        { k50,    k51,    k52,    k53,    k54,    k55,    k56,     KC_NO   }, \
+        { k60,    k61,    k62,    k63,    k64,    KC_NO,  k66,     k67     }, \
+        { k70,    k71,    k72,    k73,    k74,    k75,    k76,     KC_NO   }, \
+        { k80,    k81,    k82,    k83,    KC_NO  ,KC_NO,  k86,     k87}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,k93,    k94,    k95,    k96,     k97}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,KC_NO,  kA4,    kA5,    kA6,     kA7}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,kB3,    kB4,    kB5,    kB6,     kB7}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,KC_NO,  KC_NO,  KC_NO,  k84,     k85}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,kD3,    kD4,    kD5,    kD6,     kD7}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,kE3,    kE4,    kE5,    kE6,     kE7}, \
+        { KC_NO,  KC_NO  ,KC_NO  ,KC_NO,  kF4,    kF5,    kF6,     kF7} \
+}
+
+
+/*    4y0   A  4y1   B  4y2      4y3   D  4y4   E  4y5   F  4y6   G  4y7   H  5y0   I  5y1   J  5y2   K  5y3   L  5y4   M  5y5   N  5y6   O  5y7  P  */
+
+/*
+					0	1	2	3	4	5	6	7	8	9	A	B	C	D	E	F
+                                        A       B       C       D       E       F       G       H       I       J       K       L       M       N       O       P
+                                        4y0     4y1     4y2     4y3     4y4     4y5     4y6     4y7     5y0     5y1     5y2     5y3     5y4     5y5     5y6     5y7
+                                        r0      r1      r2       r3 r4  r5      r6      r7      r8      r9      r10     r11     r12     r13     r14     r15
+0       PB0             21      c0      f6      f8      f7      5       4       3       2       1       =+
+1       PB1             22      c1      f3      f5      f4      t       r       e       w       q       TAB
+2       PB2             23      c2      ESC     f2      f1      g       f       d       s       a       CL
+3       PB3             24      c3      f9      f11     f10     b       v       c       x       z       LS      UP              DN              [{      ]}
+4       PB4             25      c4  f12 SL      PS      RT              LT      §±      `~              6       7       8               9       0       -_
+5       PB5             26      c5      PB      PGM     KPD     LA              HM              END             y       u       i               o       p       \
+6       PB6             27      c6                      LC      DEL     BS      RC      ENT     SP      h       j       k               l       ;:      '"
+7       PB7             28      c7                                      RA              PU              PD      n       m       ,<              .>      /?      RS
+*/
+
+
+#endif

keyboards/kinesis/matrix.c

@@ -0,0 +1,228 @@
+/*
+Copyright 2014 Warren Janssens <warren.janssens@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+/*
+ * scan matrix
+ */
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#include "action_layer.h"
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "matrix.h"
+#include "led.h"
+#include "config.h"
+
+#ifndef DEBOUNCE
+#   define DEBOUNCE	5
+#endif
+static uint8_t debouncing = DEBOUNCE;
+
+/* matrix state(1:on, 0:off) */
+static uint8_t matrix[MATRIX_ROWS];
+static uint8_t matrix_debouncing[MATRIX_ROWS];
+
+static matrix_row_t read_row(uint8_t row);
+static void unselect_rows(void);
+static void select_rows(uint8_t row);
+
+__attribute__ ((weak))
+void matrix_init_quantum(void) {
+    matrix_init_kb();
+}
+
+__attribute__ ((weak))
+void matrix_scan_quantum(void) {
+    matrix_scan_kb();
+}
+
+__attribute__ ((weak))
+void matrix_init_kb(void) {
+    matrix_init_user();
+}
+
+__attribute__ ((weak))
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+inline
+uint8_t matrix_rows(void)
+{
+    return MATRIX_ROWS;
+}
+
+
+inline
+uint8_t matrix_cols(void)
+{
+    return MATRIX_COLS;
+}
+
+void matrix_init(void)
+{
+    //debug_enable = true;
+    
+    //dprint("matrix_init"); dprintln();
+    // output high (leds)
+    DDRD    = 0xFF;
+    PORTD   = 0xFF;
+    
+    // output low (multiplexers)
+    DDRF    = 0xFF;
+    PORTF   = 0x00;
+    
+    // input with pullup (matrix)
+    DDRB    = 0x00;
+    PORTB   = 0xFF;
+    
+    // input with pullup (program and keypad buttons)
+    DDRC    = 0x00;
+    PORTC   = 0xFF;
+    
+    // initialize row and col
+    unselect_rows();
+
+    // initialize matrix state: all keys off
+    for (uint8_t i=0; i < MATRIX_ROWS; i++) {
+        matrix[i] = 0;
+        matrix_debouncing[i] = 0;
+    }
+	
+}
+
+uint8_t matrix_scan(void)
+{
+
+    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+        select_rows(i);
+        uint8_t row = read_row(i);
+        if (matrix_debouncing[i] != row) {
+            matrix_debouncing[i] = row;
+            if (debouncing) {
+                debug("bounce!: "); debug_hex(debouncing); debug("\n");
+            }
+            debouncing = DEBOUNCE;
+        }
+        unselect_rows();
+    }
+
+    if (debouncing) {
+        if (--debouncing) {
+            _delay_ms(1);
+        } else {
+            for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+                matrix[i] = matrix_debouncing[i];
+            }
+        }
+    }
+    matrix_scan_quantum();
+    return 1;
+}
+
+bool matrix_is_modified(void)
+{
+    if (debouncing) return false;
+    return true;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+    return (matrix[row] & ((matrix_row_t)1<<col));
+}
+
+inline
+matrix_row_t matrix_get_row(uint8_t row)
+{
+    return matrix[row];
+}
+
+void matrix_print(void)
+{
+    print("\nr/c 01234567\n");
+    for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+        phex(row); print(": ");
+        pbin_reverse(matrix_get_row(row));
+        print("\n");
+    }
+}
+
+uint8_t matrix_key_count(void)
+{
+    uint8_t count = 0;
+    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+        count += bitpop16(matrix[i]);
+    }
+    return count;
+}
+
+static matrix_row_t read_row(uint8_t row)
+{
+	_delay_us(30);  // without this wait read unstable value.
+
+	//keypad and program buttons
+	if (row == 12)
+	{
+		return ~(PINC | 0b00111111);
+	}
+	return ~PINB;
+}
+
+static void unselect_rows(void)
+{
+    // set A,B,C,G to 0 (F4 - F7)
+    PORTF &= 0x0F;
+}
+
+static void select_rows(uint8_t row)
+{
+    // set A,B,C,G to row value
+    PORTF |= row << 4;
+}
+
+
+/* Row pin configuration
+PF0		A
+PF1		B
+PF2		C
+PF3		G	0 = U4, 1 = U5
+
+				4y0	4y1	4y2	4y3	4y4	4y5	4y6	4y7	5y0	5y1	5y2	5y3	5y4	5y5	5y6	5y7	
+				r1	r2	 r3 r4	r5	r6	r7	r8	r9	r10	r11	r12	r13	r14	r15	r16	
+PB0		21	c1	f6	f8	f7	5	4	3	2	1	=+								
+PB1		22	c2	f3	f5	f4	t	r	e	w	q	TAB								
+PB2		23	c3	ESC	f2	f1	g	f	d	s	a	CL								
+PB3		24	c4	f9	f11	f10	b	v	c	x	z	LS	UP		DN		[{	]}		
+PB4		25	c5  f12	SL	PS	RT		LT	§±	`~		6	7	8		9	0	-_ 	
+PB5		26	c6	PB	PGM	KPD							y	u	i		o	p	\	
+PB6		27	c7  			LC	DL	BS	RC	EN	SP	h	j	k		l	;:	'"	
+PB7		28	c8					RA		PU		PD	n	m	,<		.>	/?	RS	
+ */
+
+

keyboards/kinesis/readme.md

@@ -0,0 +1,42 @@
+kinesis-advantage keyboard firmware
+======================
+
+## Kinesis specific information
+This is a port of https://github.com/alvicstep/tmk_keyboard, 
+which is a fork of https://github.com/wjanssens/tmk_keyboard, 
+which is based on work from https://github.com/chrisandreae/keyboard-firmware
+
+If you replace the kinesis CPU as described in the doc folder, then this code should allow you to use QMK. 
+I've tested with a Teensy 2++, remember to change the CPU if you use a 32u4 instead. 
+
+Not yet implemented: 
+- Kinesis EEProm reading or writing
+- Audio - this should be simple if we remove hardcoded pins from audio.h and switch to E7
+
+
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/kinesis-advantage folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+
+```
+$ make keymap=[default|jack|<name>]
+```
+
+Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`