|
|
@@ -1,74 +1,3 @@
|
|
|
-
|
|
|
-
|
|
|
-# MCU name
|
|
|
-#MCU = at90usb1287
|
|
|
-MCU = atmega32u4
|
|
|
-
|
|
|
-# Processor frequency.
|
|
|
-# This will define a symbol, F_CPU, in all source code files equal to the
|
|
|
-# processor frequency in Hz. You can then use this symbol in your source code to
|
|
|
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
|
-# automatically to create a 32-bit value in your source code.
|
|
|
-#
|
|
|
-# This will be an integer division of F_USB below, as it is sourced by
|
|
|
-# F_USB after it has run through any CPU prescalers. Note that this value
|
|
|
-# does not *change* the processor frequency - it should merely be updated to
|
|
|
-# reflect the processor speed set externally so that the code can use accurate
|
|
|
-# software delays.
|
|
|
-F_CPU = 16000000
|
|
|
-
|
|
|
-
|
|
|
-#
|
|
|
-# LUFA specific
|
|
|
-#
|
|
|
-# Target architecture (see library "Board Types" documentation).
|
|
|
-ARCH = AVR8
|
|
|
-
|
|
|
-# Input clock frequency.
|
|
|
-# This will define a symbol, F_USB, in all source code files equal to the
|
|
|
-# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
|
-# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
|
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
|
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
|
-# at the end, this will be done automatically to create a 32-bit value in your
|
|
|
-# source code.
|
|
|
-#
|
|
|
-# If no clock division is performed on the input clock inside the AVR (via the
|
|
|
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
|
-F_USB = $(F_CPU)
|
|
|
-
|
|
|
-# Interrupt driven control endpoint task(+60)
|
|
|
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
-
|
|
|
-
|
|
|
-# Boot Section Size in *bytes*
|
|
|
-# Teensy halfKay 512
|
|
|
-# Teensy++ halfKay 1024
|
|
|
-# Atmel DFU loader 4096
|
|
|
-# LUFA bootloader 4096
|
|
|
-# USBaspLoader 2048
|
|
|
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
-
|
|
|
-
|
|
|
-# Build Options
|
|
|
-# comment out to disable the options.
|
|
|
-#
|
|
|
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
|
|
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
|
|
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
|
|
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
|
|
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
|
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
|
|
|
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
|
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
|
|
|
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
|
|
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
|
|
|
-# MIDI_ENABLE ?= YES # MIDI controls
|
|
|
-# UNICODE_ENABLE ?= YES # Unicode
|
|
|
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
|
|
-RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
|
|
|
-
|
|
|
-ifndef QUANTUM_DIR
|
|
|
+ifndef MAKEFILE_INCLUDED
|
|
|
include ../../Makefile
|
|
|
endif
|
|
|
-
|
Jack Humbert