Delete lcd_backlight_hal.c

The functionality can now be found in the infinity_erogodox.c file
instead.

keyboards/infinity_ergodox/infinity_ergodox.c

@@ -2,6 +2,7 @@
 #include "ch.h"
 #include "hal.h"
 #include "serial_link/system/serial_link.h"
+#include "lcd_backlight.h"
 
 void init_serial_link_hal(void) {
     PORTA->PCR[1] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(2);
@@ -9,3 +10,67 @@ void init_serial_link_hal(void) {
     PORTE->PCR[0] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(3);
     PORTE->PCR[1] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(3);
 }
+
+#define RED_PIN 1
+#define GREEN_PIN 2
+#define BLUE_PIN 3
+#define CHANNEL_RED FTM0->CHANNEL[0]
+#define CHANNEL_GREEN FTM0->CHANNEL[1]
+#define CHANNEL_BLUE FTM0->CHANNEL[2]
+
+#define RGB_PORT PORTC
+#define RGB_PORT_GPIO GPIOC
+
+// Base FTM clock selection (72 MHz system clock)
+// @ 0xFFFF period, 72 MHz / (0xFFFF * 2) = Actual period
+// Higher pre-scalar will use the most power (also look the best)
+// Pre-scalar calculations
+// 0 -      72 MHz -> 549 Hz
+// 1 -      36 MHz -> 275 Hz
+// 2 -      18 MHz -> 137 Hz
+// 3 -       9 MHz ->  69 Hz (Slightly visible flicker)
+// 4 -   4 500 kHz ->  34 Hz (Visible flickering)
+// 5 -   2 250 kHz ->  17 Hz
+// 6 -   1 125 kHz ->   9 Hz
+// 7 - 562 500  Hz ->   4 Hz
+// Using a higher pre-scalar without flicker is possible but FTM0_MOD will need to be reduced
+// Which will reduce the brightness range
+#define PRESCALAR_DEFINE 0
+
+void lcd_backlight_hal_init(void) {
+	// Setup Backlight
+    SIM->SCGC6 |= SIM_SCGC6_FTM0;
+    FTM0->CNT = 0; // Reset counter
+
+	// PWM Period
+	// 16-bit maximum
+	FTM0->MOD = 0xFFFF;
+
+	// Set FTM to PWM output - Edge Aligned, Low-true pulses
+#define CNSC_MODE FTM_SC_CPWMS | FTM_SC_PS(4) | FTM_SC_CLKS(0)
+	CHANNEL_RED.CnSC = CNSC_MODE;
+	CHANNEL_GREEN.CnSC = CNSC_MODE;
+	CHANNEL_BLUE.CnSC = CNSC_MODE;
+
+	// System clock, /w prescalar setting
+	FTM0->SC = FTM_SC_CLKS(1) | FTM_SC_PS(PRESCALAR_DEFINE);
+
+	CHANNEL_RED.CnV = 0;
+	CHANNEL_GREEN.CnV = 0;
+	CHANNEL_BLUE.CnV = 0;
+
+	RGB_PORT_GPIO->PDDR |= (1 << RED_PIN);
+	RGB_PORT_GPIO->PDDR |= (1 << GREEN_PIN);
+	RGB_PORT_GPIO->PDDR |= (1 << BLUE_PIN);
+
+#define RGB_MODE PORTx_PCRn_SRE | PORTx_PCRn_DSE | PORTx_PCRn_MUX(4)
+    RGB_PORT->PCR[RED_PIN] = RGB_MODE;
+    RGB_PORT->PCR[GREEN_PIN] = RGB_MODE;
+    RGB_PORT->PCR[BLUE_PIN] = RGB_MODE;
+}
+
+void lcd_backlight_hal_color(uint16_t r, uint16_t g, uint16_t b) {
+	CHANNEL_RED.CnV = r;
+	CHANNEL_GREEN.CnV = g;
+	CHANNEL_BLUE.CnV = b;
+}

keyboards/infinity_ergodox/lcd_backlight_hal.c

@@ -1,84 +0,0 @@
-/*
-Copyright 2016 Fred Sundvik <fsundvik@gmail.com>
-Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-#include "lcd_backlight.h"
-#include "hal.h"
-
-#define RED_PIN 1
-#define GREEN_PIN 2
-#define BLUE_PIN 3
-#define CHANNEL_RED FTM0->CHANNEL[0]
-#define CHANNEL_GREEN FTM0->CHANNEL[1]
-#define CHANNEL_BLUE FTM0->CHANNEL[2]
-
-#define RGB_PORT PORTC
-#define RGB_PORT_GPIO GPIOC
-
-// Base FTM clock selection (72 MHz system clock)
-// @ 0xFFFF period, 72 MHz / (0xFFFF * 2) = Actual period
-// Higher pre-scalar will use the most power (also look the best)
-// Pre-scalar calculations
-// 0 -      72 MHz -> 549 Hz
-// 1 -      36 MHz -> 275 Hz
-// 2 -      18 MHz -> 137 Hz
-// 3 -       9 MHz ->  69 Hz (Slightly visible flicker)
-// 4 -   4 500 kHz ->  34 Hz (Visible flickering)
-// 5 -   2 250 kHz ->  17 Hz
-// 6 -   1 125 kHz ->   9 Hz
-// 7 - 562 500  Hz ->   4 Hz
-// Using a higher pre-scalar without flicker is possible but FTM0_MOD will need to be reduced
-// Which will reduce the brightness range
-#define PRESCALAR_DEFINE 0
-
-void lcd_backlight_hal_init(void) {
-	// Setup Backlight
-    SIM->SCGC6 |= SIM_SCGC6_FTM0;
-    FTM0->CNT = 0; // Reset counter
-
-	// PWM Period
-	// 16-bit maximum
-	FTM0->MOD = 0xFFFF;
-
-	// Set FTM to PWM output - Edge Aligned, Low-true pulses
-#define CNSC_MODE FTM_SC_CPWMS | FTM_SC_PS(4) | FTM_SC_CLKS(0)
-	CHANNEL_RED.CnSC = CNSC_MODE;
-	CHANNEL_GREEN.CnSC = CNSC_MODE;
-	CHANNEL_BLUE.CnSC = CNSC_MODE;
-
-	// System clock, /w prescalar setting
-	FTM0->SC = FTM_SC_CLKS(1) | FTM_SC_PS(PRESCALAR_DEFINE);
-
-	CHANNEL_RED.CnV = 0;
-	CHANNEL_GREEN.CnV = 0;
-	CHANNEL_BLUE.CnV = 0;
-
-	RGB_PORT_GPIO->PDDR |= (1 << RED_PIN);
-	RGB_PORT_GPIO->PDDR |= (1 << GREEN_PIN);
-	RGB_PORT_GPIO->PDDR |= (1 << BLUE_PIN);
-
-#define RGB_MODE PORTx_PCRn_SRE | PORTx_PCRn_DSE | PORTx_PCRn_MUX(4)
-    RGB_PORT->PCR[RED_PIN] = RGB_MODE;
-    RGB_PORT->PCR[GREEN_PIN] = RGB_MODE;
-    RGB_PORT->PCR[BLUE_PIN] = RGB_MODE;
-}
-
-void lcd_backlight_hal_color(uint16_t r, uint16_t g, uint16_t b) {
-	CHANNEL_RED.CnV = r;
-	CHANNEL_GREEN.CnV = g;
-	CHANNEL_BLUE.CnV = b;
-}
-

quantum/visualizer/visualizer.mk

@@ -34,9 +34,6 @@ endif
 
 ifdef LCD_BACKLIGHT_ENABLE
 SRC += $(VISUALIZER_DIR)/lcd_backlight.c
-ifndef EMULATOR
-SRC += lcd_backlight_hal.c
-endif
 OPT_DEFS += -DLCD_BACKLIGHT_ENABLE
 endif