[Keyboard] wilba.tech PCB refactoring (#6982)

* Cleanup

* Refactor VIA rules.mk

* WT mono backlight refactor, VIA support

* Added WT75-C

* Fixed compile error

* Cleanup rules.mk

* Review changes

* Review changes

keyboards/aeboards/aegis/config.h

@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

keyboards/aeboards/ext65/config.h

@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

keyboards/snagpad/config.h

@@ -48,9 +48,6 @@
 #define RGBLIGHT_VAL_STEP 8
 #endif
 
-// Does not use WT_MONO_BACKLIGHT
-// #define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

keyboards/wilba_tech/rama_works_koyu/rules.mk

@@ -1,5 +1,3 @@
-
-
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c \
 		keyboards/wilba_tech/wt_rgb_backlight.c \
@@ -10,42 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

keyboards/wilba_tech/rama_works_m10_b/config.h

@@ -181,8 +181,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

keyboards/wilba_tech/rama_works_m10_b/rules.mk

@@ -4,44 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/rama_works_m60_a/rules.mk

@@ -10,42 +10,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

keyboards/wilba_tech/rama_works_m6_a/rules.mk

@@ -4,43 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

keyboards/wilba_tech/rama_works_m6_b/rules.mk

@@ -5,47 +5,17 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 		drivers/issi/is31fl3218.c \
 		drivers/avr/i2c_master.c
 
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

keyboards/wilba_tech/rama_works_u80_a/config.h

@@ -179,8 +179,6 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 // IS31FL3731 driver
 #define DRIVER_COUNT 3
 #define DRIVER_LED_TOTAL 108

keyboards/wilba_tech/rama_works_u80_a/rules.mk

@@ -8,44 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt60_a/config.h

@@ -179,14 +179,33 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// enable the RGB indicator for WT75-A
+#define MONO_BACKLIGHT_WT75_A
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +213,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*5*14*2)) = (37+560)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 597
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 427
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*5*14*2)) = (44+560)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 604
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 420
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt60_a/rules.mk

@@ -1,6 +1,7 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		

keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk

@@ -1,68 +1,2 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt60_d/rules.mk

@@ -1,50 +1,19 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/wilba_tech/wt65_a/config.h

@@ -179,14 +179,30 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +210,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*5*15*2)) = (37+600)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 637
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 387
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after  backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*5*15*2)) = (44+600)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 644
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 380
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt65_a/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt65_a/rules.mk

@@ -1,50 +1,21 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt65_b/config.h

@@ -179,14 +179,30 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +210,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*5*15*2)) = (37+600)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 637
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 387
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after  backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*5*15*2)) = (44+600)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 644
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 380
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt65_b/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt65_b/rules.mk

@@ -1,50 +1,21 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt69_a/keymaps/via/rules.mk

@@ -1,68 +1,2 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt69_a/rules.mk

@@ -1,47 +1,17 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt75_a/config.h

@@ -179,14 +179,33 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// enable the RGB indicator for WT75-A
+#define MONO_BACKLIGHT_WT75_A
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +213,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*6*15*2)) = (37+720)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 757
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 267
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*6*15*2)) = (44+720)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 764
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 260
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt75_a/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt75_a/rules.mk

@@ -1,50 +1,21 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt75_b/config.h

@@ -179,14 +179,33 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// enable the RGB indicator for WT75-A
+#define MONO_BACKLIGHT_WT75_A
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +213,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*6*16*2)) = (37+768)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 805
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 219
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*6*16*2)) = (44+768)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 812
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 212
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt75_b/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt75_b/rules.mk

@@ -1,50 +1,21 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt75_c/config.h

@@ -0,0 +1,223 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6582 // wilba.tech
+#define PRODUCT_ID      0x075C // 75-C
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    wilba.tech
+#define PRODUCT         wilba.tech WT75-C
+#define DESCRIPTION     wilba.tech WT75-C
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 16
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F1, F0, E6, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, B7, D4 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// enable the RGB indicator for WT75-A
+#define MONO_BACKLIGHT_WT75_A
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
+
+#define DYNAMIC_KEYMAP_LAYER_COUNT 4
+
+// EEPROM usage
+
+// TODO: refactor with new user EEPROM code (coming soon)
+#define EEPROM_MAGIC 0x4520
+#define EEPROM_MAGIC_ADDR 34
+// Bump this every time we change what we store
+// This will automatically reset the EEPROM with defaults
+// and avoid loading invalid data from the EEPROM
+#define EEPROM_VERSION 0x08
+#define EEPROM_VERSION_ADDR 36
+
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*6*16*2)) = (44+768)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 812
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 212
+#define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt75_c/keymaps/default/keymap.c

@@ -0,0 +1,41 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	// Default layer
+	[0] = LAYOUT_all(
+		KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_PSCR,
+		KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_BSPC, KC_DEL,
+		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_PGUP,
+		KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,                    KC_PGDN,
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,                   KC_UP,
+		KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, MO(1),            KC_LEFT, KC_DOWN, KC_RGHT),
+
+	// Fn1 Layer
+	[1] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn2 Layer
+	[2] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn3 Layer
+	[3] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+};
+

keyboards/wilba_tech/wt75_c/keymaps/via/keymap.c

@@ -0,0 +1,41 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	// Default layer
+	[0] = LAYOUT_all(
+		KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_PSCR,
+		KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_BSPC, KC_DEL,
+		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_PGUP,
+		KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,                    KC_PGDN,
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,                   KC_UP,
+		KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, MO(1),            KC_LEFT, KC_DOWN, KC_RGHT),
+
+	// Fn1 Layer
+	[1] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn2 Layer
+	[2] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+
+	// Fn3 Layer
+	[3] = LAYOUT_all(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,
+		KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS, KC_TRNS),
+};
+

keyboards/wilba_tech/wt75_c/keymaps/via/rules.mk

@@ -0,0 +1,2 @@
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt75_c/readme.md

@@ -0,0 +1,13 @@
+# wilba.tech WT75-C
+
+WT75-C is a keyboard PCB supporting 75% layout with offset arrow keys. [More info at wilba.tech](https://wilba.tech/)
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: wilba.tech WT75-C  
+Hardware Availability: Custom keyboard group buys
+
+Make example for this keyboard (after setting up your build environment):
+
+    make wilba_tech/wt75_c:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/wilba_tech/wt75_c/rules.mk

@@ -0,0 +1,39 @@
+# project specific files
+SRC =	drivers/issi/is31fl3736.c \
+		drivers/avr/i2c_master.c \
+		quantum/color.c \
+		keyboards/wilba_tech/wt_mono_backlight.c \
+		keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches

keyboards/wilba_tech/wt75_c/wt75_c.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/wilba_tech/wt75_c/wt75_c.h

@@ -0,0 +1,46 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+// Right switch of split backspace is at 2,13 and is the only switch
+// whose physical position doesn't match switch matrix position :-(
+// However, it also makes no sense to view the physical as 16 columns,
+// so the numbering goes 00 to 14. Deal with it.
+//
+// 0,15 exists on PCB but is blocked by the 7V blocker so until someone
+// designs a case that uses it, we can just forget it exists.
+
+#define LAYOUT_all( \
+    K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012,       K014,       \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213,       K215, \
+    K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,             K315, \
+    K400, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412,             K413,       \
+    K500, K501, K502,                   K506,                   K510, K511,       K512, K513, K515  \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, ____, K014, ____ }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, ____, K215 }, \
+    { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, ____, ____, K315 }, \
+    { K400, ____, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, ____, ____ }, \
+    { K500, K501, K502, ____, ____, ____, K506, ____, ____, ____, K510, K511, K512, K513, ____, K515 }  \
+}
+

keyboards/wilba_tech/wt80_a/config.h

@@ -179,14 +179,30 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +210,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*6*17*2)) = (37+816)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 853
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 171
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*6*17*2)) = (44+816)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 860
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 164
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt80_a/keymaps/via/rules.mk

@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt80_a/rules.mk

@@ -1,50 +1,21 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

keyboards/wilba_tech/wt8_a/rules.mk

@@ -1,50 +1,19 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/wilba_tech/wt_main.c

@@ -20,9 +20,9 @@
 #if RGB_BACKLIGHT_ENABLED
 #include "keyboards/wilba_tech/wt_rgb_backlight.h"
 #endif // RGB_BACKLIGHT_ENABLED
-#ifdef WT_MONO_BACKLIGHT
+#if MONO_BACKLIGHT_ENABLED
 #include "keyboards/wilba_tech/wt_mono_backlight.h"
-#endif // WT_MONO_BACKLIGHT
+#endif // MONO_BACKLIGHT_ENABLED
 #include "keyboards/wilba_tech/via_api.h" // Temporary hack
 #include "keyboards/wilba_tech/via_keycodes.h" // Temporary hack
 
@@ -150,7 +150,7 @@ void raw_hid_receive( uint8_t *data, uint8_t length )
 			break;
 		}
 #endif // DYNAMIC_KEYMAP_ENABLE
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 		case id_backlight_config_set_value:
 		{
 			backlight_config_set_value(command_data);
@@ -166,7 +166,7 @@ void raw_hid_receive( uint8_t *data, uint8_t length )
 			backlight_config_save();
 			break;
 		}
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 		case id_eeprom_reset:
 		{
 			eeprom_reset();
@@ -202,16 +202,16 @@ void main_init(void)
 	// If the EEPROM has the magic, the data is good.
 	// OK to load from EEPROM.
 	if (eeprom_is_valid()) {
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 		backlight_config_load();
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	} else	{
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 		// If the EEPROM has not been saved before, or is out of date,
 		// save the default values to the EEPROM. Default values
-		// come from construction of the zeal_backlight_config instance.
+		// come from construction of the backlight_config instance.
 		backlight_config_save();
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 #ifdef DYNAMIC_KEYMAP_ENABLE
 		// This resets the keymaps in EEPROM to what is in flash.
 		dynamic_keymap_reset();
@@ -222,20 +222,13 @@ void main_init(void)
 		eeprom_set_valid(true);
 	}
 	
-#if RGB_BACKLIGHT_ENABLED
-	// Initialize LED drivers for backlight.
-	backlight_init_drivers();
-
-	backlight_timer_init();
-	backlight_timer_enable();
-#endif // RGB_BACKLIGHT_ENABLED
-#ifdef WT_MONO_BACKLIGHT
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	// Initialize LED drivers for backlight.
 	backlight_init_drivers();
 
 	backlight_timer_init();
 	backlight_timer_enable();
-#endif // WT_MONO_BACKLIGHT
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 }
 
 void bootmagic_lite(void)
@@ -267,22 +260,18 @@ void matrix_init_kb(void)
 
 void matrix_scan_kb(void)
 {
-#if RGB_BACKLIGHT_ENABLED
-	// This only updates the LED driver buffers if something has changed.
-	backlight_update_pwm_buffers();
-#endif // RGB_BACKLIGHT_ENABLED
-#ifdef WT_MONO_BACKLIGHT
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	// This only updates the LED driver buffers if something has changed.
 	backlight_update_pwm_buffers();
-#endif
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	matrix_scan_user();
 }
 
 bool process_record_kb(uint16_t keycode, keyrecord_t *record)
 {
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	process_record_backlight(keycode, record);
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 
 	switch(keycode) {
 		case FN_MO13:
@@ -372,22 +361,23 @@ void action_function(keyrecord_t *record, uint8_t id, uint8_t opt)
 
 void led_set_kb(uint8_t usb_led)
 {
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	backlight_set_indicator_state(usb_led);
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
+	led_set_user(usb_led);
 }
 
 void suspend_power_down_kb(void)
 {
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	backlight_set_suspend_state(true);
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 }
 
 void suspend_wakeup_init_kb(void)
 {
-#if RGB_BACKLIGHT_ENABLED
+#if RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 	backlight_set_suspend_state(false);
-#endif // RGB_BACKLIGHT_ENABLED
+#endif // RGB_BACKLIGHT_ENABLED || MONO_BACKLIGHT_ENABLED
 }
 

keyboards/wilba_tech/wt_mono_backlight.c

@@ -14,20 +14,43 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#include "quantum.h"
 #include "wt_mono_backlight.h"
+#include "wt_rgb_backlight_api.h" // reuse these for now
+#include "wt_rgb_backlight_keycodes.h" // reuse these for now
+
 #include "drivers/avr/i2c_master.h"
 #include "drivers/issi/is31fl3736.h"
-
 #include <avr/interrupt.h>
 
+#include "progmem.h"
+#include "quantum/color.h"
+
 #define ISSI_ADDR_DEFAULT 0x50
 
+#define BACKLIGHT_EFFECT_MAX 3
+
+#ifndef MONO_BACKLIGHT_COLOR_1
+#define MONO_BACKLIGHT_COLOR_1 { .h = 0, .s = 255 }
+#endif
+
+backlight_config g_config = {
+    .disable_when_usb_suspended = MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED,
+    .disable_after_timeout = MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT,
+    .brightness = MONO_BACKLIGHT_BRIGHTNESS,
+    .effect = MONO_BACKLIGHT_EFFECT,
+    .effect_speed = MONO_BACKLIGHT_EFFECT_SPEED,
+    .color_1 = MONO_BACKLIGHT_COLOR_1,
+};
+
 bool g_suspend_state = false;
+uint8_t g_indicator_state = 0;
 
 // Global tick at 20 Hz
 uint32_t g_tick = 0;
-uint8_t g_config_effect_speed = 0;
-uint8_t g_config_brightness = 255;
+
+// Ticks since any key was last hit.
+uint32_t g_any_key_hit = 0;
 
 void backlight_init_drivers(void)
 {
@@ -41,6 +64,10 @@ void backlight_init_drivers(void)
 	IS31FL3736_update_led_control_registers( ISSI_ADDR_DEFAULT, 0x00 );
 }
 
+void backlight_set_key_hit(uint8_t row, uint8_t column)
+{
+    g_any_key_hit = 0;
+}
 
 // This is (F_CPU/1024) / 20 Hz
 // = 15625 Hz / 20 Hz
@@ -82,13 +109,63 @@ void backlight_set_suspend_state(bool state)
 	g_suspend_state = state;
 }
 
+void backlight_set_indicator_state(uint8_t state)
+{
+    g_indicator_state = state;
+}
+
+void backlight_set_brightness_all( uint8_t value )
+{
+	IS31FL3736_mono_set_brightness_all( value );
+}
+
+void backlight_effect_all_off(void)
+{
+	IS31FL3736_mono_set_brightness_all( 0 );
+}
+
+void backlight_effect_all_on(void)
+{
+	IS31FL3736_mono_set_brightness_all( g_config.brightness );
+}
+
+void backlight_effect_raindrops(bool initialize)
+{
+    // Change one LED every tick
+    uint8_t led_to_change = ( g_tick & 0x000 ) == 0 ? rand() % 96 : 255;
+
+    for ( int i=0; i<96; i++ )
+    {
+        // If initialize, all get set to random brightness
+        // If not, all but one will stay the same as before.
+        if ( initialize || i == led_to_change )
+        {
+            IS31FL3736_mono_set_brightness(i, rand() & 0xFF );
+        }
+    }
+}
+
 void backlight_effect_cycle_all(void)
 {
-	uint8_t offset = ( g_tick << g_config_effect_speed ) & 0xFF;
+	uint8_t offset = ( g_tick << g_config.effect_speed ) & 0xFF;
 
 	backlight_set_brightness_all( offset );
 }
 
+// This runs after another backlight effect and replaces
+// colors already set
+void backlight_effect_indicators(void)
+{
+#if defined(MONO_BACKLIGHT_WT75_A)
+    HSV hsv = { .h = g_config.color_1.h, .s = g_config.color_1.s, .v = g_config.brightness };
+    RGB rgb = hsv_to_rgb( hsv );
+    // G8, H8, I8 -> (6*8+7) (7*8+7), (8*8+7)
+    IS31FL3736_mono_set_brightness(55, rgb.r);
+    IS31FL3736_mono_set_brightness(63, rgb.g);
+    IS31FL3736_mono_set_brightness(71, rgb.b);
+#endif // MONO_BACKLIGHT_WT75_A
+}
+
 ISR(TIMER3_COMPA_vect)
 {
 	// delay 1 second before driving LEDs or doing anything else
@@ -100,8 +177,154 @@ ISR(TIMER3_COMPA_vect)
 
 	g_tick++;
 
-	//backlight_effect_cycle_all();
-	backlight_set_brightness_all( 255 );
+    if ( g_any_key_hit < 0xFFFFFFFF )
+    {
+        g_any_key_hit++;
+    }
+
+    // Ideally we would also stop sending zeros to the LED driver PWM buffers
+    // while suspended and just do a software shutdown. This is a cheap hack for now.
+    bool suspend_backlight = ((g_suspend_state && g_config.disable_when_usb_suspended) ||
+            (g_config.disable_after_timeout > 0 && g_any_key_hit > g_config.disable_after_timeout * 60 * 20));
+    uint8_t effect = suspend_backlight ? 0 : g_config.effect;
+
+    // Keep track of the effect used last time,
+    // detect change in effect, so each effect can
+    // have an optional initialization.
+    static uint8_t effect_last = 255;
+    bool initialize = effect != effect_last;
+    effect_last = effect;
+
+    // this gets ticked at 20 Hz.
+    // each effect can opt to do calculations
+    // and/or request PWM buffer updates.
+    switch ( effect )
+    {
+        case 0:
+            backlight_effect_all_off();
+            break;
+        case 1:
+            backlight_effect_all_on();;
+            break;
+        case 2:
+            backlight_effect_raindrops(initialize);
+            break;
+        default:
+            backlight_effect_all_off();
+            break;
+	}
+
+    if ( ! suspend_backlight )
+    {
+        backlight_effect_indicators();
+    }
+}
+
+// Some helpers for setting/getting HSV
+void _set_color( HS *color, uint8_t *data )
+{
+    color->h = data[0];
+    color->s = data[1];
+}
+
+void _get_color( HS *color, uint8_t *data )
+{
+    data[0] = color->h;
+    data[1] = color->s;
+}
+
+void backlight_config_set_value( uint8_t *data )
+{
+    bool reinitialize = false;
+    uint8_t *value_id = &(data[0]);
+    uint8_t *value_data = &(data[1]);
+    switch ( *value_id )
+    {
+        case id_disable_when_usb_suspended:
+        {
+            g_config.disable_when_usb_suspended = (bool)*value_data;
+            break;
+        }
+        case id_disable_after_timeout:
+        {
+            g_config.disable_after_timeout = *value_data;
+            break;
+        }
+        case id_brightness:
+        {
+            g_config.brightness = *value_data;
+            break;
+        }
+        case id_effect:
+        {
+            g_config.effect = *value_data;
+            break;
+        }
+        case id_effect_speed:
+        {
+            g_config.effect_speed = *value_data;
+            break;
+        }
+        case id_color_1:
+        {
+            _set_color( &(g_config.color_1), value_data );
+            break;
+        }
+    }
+
+    if ( reinitialize )
+    {
+        backlight_init_drivers();
+    }
+}
+
+void backlight_config_get_value( uint8_t *data )
+{
+    uint8_t *value_id = &(data[0]);
+    uint8_t *value_data = &(data[1]);
+    switch ( *value_id )
+    {
+        case id_disable_when_usb_suspended:
+        {
+            *value_data = ( g_config.disable_when_usb_suspended ? 1 : 0 );
+            break;
+        }
+        case id_disable_after_timeout:
+        {
+            *value_data = g_config.disable_after_timeout;
+            break;
+        }
+        case id_brightness:
+        {
+            *value_data = g_config.brightness;
+            break;
+        }
+        case id_effect:
+        {
+            *value_data = g_config.effect;
+            break;
+        }
+        case id_effect_speed:
+        {
+            *value_data = g_config.effect_speed;
+            break;
+        }
+        case id_color_1:
+        {
+            _get_color( &(g_config.color_1), value_data );
+            break;
+        }
+    }
+}
+
+void backlight_config_load(void)
+{
+    eeprom_read_block( &g_config, ((void*)MONO_BACKLIGHT_CONFIG_EEPROM_ADDR), sizeof(backlight_config) );
+}
+
+void backlight_config_save(void)
+{
+    eeprom_update_block( &g_config, ((void*)MONO_BACKLIGHT_CONFIG_EEPROM_ADDR), sizeof(backlight_config) );
 }
 
 void backlight_update_pwm_buffers(void)
@@ -109,8 +332,110 @@ void backlight_update_pwm_buffers(void)
 	IS31FL3736_update_pwm_buffers(ISSI_ADDR_DEFAULT,0x00);
 }
 
-void backlight_set_brightness_all( uint8_t value )
+bool process_record_backlight(uint16_t keycode, keyrecord_t *record)
 {
-	IS31FL3736_mono_set_brightness_all( value );
+    // Record keypresses for backlight effects
+    if ( record->event.pressed )
+    {
+        backlight_set_key_hit( record->event.key.row, record->event.key.col );
+    }
+
+    switch(keycode)
+    {
+        case BR_INC:
+            if (record->event.pressed)
+            {
+                backlight_brightness_increase();
+            }
+            return false;
+            break;
+        case BR_DEC:
+            if (record->event.pressed)
+            {
+                backlight_brightness_decrease();
+            }
+            return false;
+            break;
+        case EF_INC:
+            if (record->event.pressed)
+            {
+                backlight_effect_increase();
+            }
+            return false;
+            break;
+        case EF_DEC:
+            if (record->event.pressed)
+            {
+                backlight_effect_decrease();
+            }
+            return false;
+            break;
+        case ES_INC:
+            if (record->event.pressed)
+            {
+                backlight_effect_speed_increase();
+            }
+            return false;
+            break;
+        case ES_DEC:
+            if (record->event.pressed)
+            {
+                backlight_effect_speed_decrease();
+            }
+            return false;
+            break;
+    }
+
+    return true;
+}
+
+// Deals with the messy details of incrementing an integer
+uint8_t increment( uint8_t value, uint8_t step, uint8_t min, uint8_t max )
+{
+    int16_t new_value = value;
+    new_value += step;
+    return MIN( MAX( new_value, min ), max );
 }
 
+uint8_t decrement( uint8_t value, uint8_t step, uint8_t min, uint8_t max )
+{
+    int16_t new_value = value;
+    new_value -= step;
+    return MIN( MAX( new_value, min ), max );
+}
+
+void backlight_effect_increase(void)
+{
+    g_config.effect = increment( g_config.effect, 1, 0, BACKLIGHT_EFFECT_MAX );
+    backlight_config_save();
+}
+
+void backlight_effect_decrease(void)
+{
+    g_config.effect = decrement( g_config.effect, 1, 0, BACKLIGHT_EFFECT_MAX );
+    backlight_config_save();
+}
+
+void backlight_effect_speed_increase(void)
+{
+    g_config.effect_speed = increment( g_config.effect_speed, 1, 0, 3 );
+    backlight_config_save();
+}
+
+void backlight_effect_speed_decrease(void)
+{
+    g_config.effect_speed = decrement( g_config.effect_speed, 1, 0, 3 );
+    backlight_config_save();
+}
+
+void backlight_brightness_increase(void)
+{
+    g_config.brightness = increment( g_config.brightness, 8, 0, 255 );
+    backlight_config_save();
+}
+
+void backlight_brightness_decrease(void)
+{
+    g_config.brightness = decrement( g_config.brightness, 8, 0, 255 );
+    backlight_config_save();
+}

keyboards/wilba_tech/wt_mono_backlight.h

@@ -19,6 +19,36 @@
 #include <stdint.h>
 #include <stdbool.h>
 
+#include "quantum/color.h"
+
+typedef struct PACKED
+{
+    uint8_t h;
+    uint8_t s;
+} HS;
+
+typedef struct
+{
+	bool disable_when_usb_suspended:1;  // |
+    bool __pad1:1;                      // |
+    bool __pad2:1;                      // |
+    bool __pad3:1;                      // |
+    bool __pad4:1;                      // |
+    bool __pad5:1;                      // |
+    bool __pad6:1;                      // |
+    bool __pad7:1;                      // 1 byte
+    uint8_t disable_after_timeout;      // 1 byte
+    uint8_t brightness;                 // 1 byte
+    uint8_t effect;                     // 1 byte
+    uint8_t effect_speed;               // 1 byte
+    HS color_1;                         // 2 bytes (Indicator Color for Xeno)
+} backlight_config;                     // = 7 bytes
+
+void backlight_config_load(void);
+void backlight_config_save(void);
+void backlight_config_set_value( uint8_t *data );
+void backlight_config_get_value( uint8_t *data );
+
 void backlight_init_drivers(void);
 
 void backlight_timer_init(void);
@@ -26,8 +56,24 @@ void backlight_timer_enable(void);
 void backlight_timer_disable(void);
 
 void backlight_set_suspend_state(bool state);
+void backlight_set_indicator_state(uint8_t state);
 
+// This should not be called from an interrupt
+// (eg. from a timer interrupt).
+// Call this while idle (in between matrix scans).
+// If the buffer is dirty, it will update the driver with the buffer.
 void backlight_update_pwm_buffers(void);
 
-void backlight_set_brightness_all( uint8_t value );
+// Handle backlight specific keycodes
+bool process_record_backlight(uint16_t keycode, keyrecord_t *record);
+
+void backlight_set_key_hit(uint8_t row, uint8_t col);
+
+void backlight_effect_increase(void);
+void backlight_effect_decrease(void);
+void backlight_effect_speed_increase(void);
+void backlight_effect_speed_decrease(void);
+
+void backlight_brightness_increase(void);
+void backlight_brightness_decrease(void);
 

keyboards/wilba_tech/zeal60/rules.mk

@@ -1,5 +1,3 @@
-
-
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c \
 		keyboards/wilba_tech/wt_rgb_backlight.c \
@@ -10,42 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

keyboards/wilba_tech/zeal65/rules.mk

@@ -1,5 +1,3 @@
-
-
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c \
 		keyboards/wilba_tech/wt_rgb_backlight.c \
@@ -10,42 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode