[Keymap] Drashna keymap updates for 0.18.0 (#18184)

Co-authored-by: Ryan <fauxpark@gmail.com>

keyboards/bastardkb/charybdis/4x6/keymaps/drashna/config.h

@@ -16,6 +16,9 @@
  */
 #pragma once
 
+#undef PRODUCT
+#define PRODUCT "Charybdis (4x6) Blackpill"
+
 #undef MATRIX_COL_PINS
 #define MATRIX_COL_PINS \
     { B0, B1, B12, B3, B4, B5 }
@@ -34,7 +37,7 @@
 #define DIODE_DIRECTION ROW2COL
 #define SPLIT_HAND_PIN A3
 #undef MASTER_RIGHT
-// #define USB_VBUS_PIN B10
+#define USB_VBUS_PIN B10
 
 #undef RGB_DI_PIN
 #define RGB_DI_PIN A1
@@ -55,6 +58,8 @@
 #define AUDIO_PWM_PAL_MODE 2
 #define AUDIO_STATE_TIMER  GPTD3
 #define AUDIO_INIT_DELAY
+#define AUDIO_ENABLE_TONE_MULTIPLEXING
+#define AUDIO_TONE_MULTIPLEXING_RATE_DEFAULT 10
 
 #undef SOFT_SERIAL_PIN
 // #define SERIAL_USART_FULL_DUPLEX  // Enable full duplex operation mode.
@@ -64,12 +69,8 @@
 // #define SERIAL_USART_TX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
 // #define SERIAL_USART_RX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
 // #define SERIAL_USART_TIMEOUT     100  // USART driver timeout. default 100
-// // #define SERIAL_USART_PIN_SWAP // swap RX and TX pins on master
-// // To use the highest possible baudrate (3.75Mbit/s) uncomment the following
-// // line, this can result in dropped communications so lower the speed if there
-// // are many timeouts.
-// // #define SERIAL_USART_SPEED (STM32_PCLK2 >> 4)
-#define SERIAL_USART_SPEED       921600
+// #define SERIAL_USART_SPEED       921600
+#define SERIAL_USART_SPEED (1.5 * 1024 * 1024)
 
 #define CRC8_USE_TABLE
 #define CRC8_OPTIMIZE_SPEED
@@ -103,3 +104,12 @@
 #define RGB_MATRIX_MAXIMUM_BRIGHTNESS 150
 
 #define CHARYBDIS_CONFIG_SYNC
+
+#define BOOTMAGIC_LITE_ROW    0
+#define BOOTMAGIC_LITE_COLUMN 0
+#define BOOTMAGIC_LITE_ROW_RIGHT    5
+#define BOOTMAGIC_LITE_COLUMN_RIGHT 0
+#define BOOTMAGIC_LITE_EEPROM_ROW    1
+#define BOOTMAGIC_LITE_EEPROM_COLUMN 0
+#define BOOTMAGIC_LITE_EEPROM_ROW_RIGHT    1
+#define BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT 0

keyboards/bastardkb/charybdis/4x6/keymaps/drashna/keymap.c

@@ -26,8 +26,8 @@
      KC_ESC,  ________________NUMBER_LEFT________________,            ________________NUMBER_RIGHT_______________, UC_CLUE, \
      SH_TT,   K01,    K02,      K03,     K04,     K05,                K06,     K07,     K08,     K09,     K0A,     SH_TT, \
      LALT_T(KC_TAB), K11, K12,  K13,     K14,     K15,                K16,     K17,     K18,     K19,     K1A,     RALT_T(K1B), \
-     OS_LSFT,CTL_T(K21),ALT_T(K22),GUI_T(K23),K24,K25,                K26,K27,RGUI_T(K28),RALT_T(K29),RCTL_T(K2A), OS_RSFT, \
-                           SFT_T(KC_GRV), UC_IRNY, OS_LGUI,    TT(_MOUSE),  KC_ENT, \
+     OS_LSFT,CTL_T(K21),  K22,  K23,     K24,     K25,                K26,K27,RGUI_T(K28),RALT_T(K29),RCTL_T(K2A), OS_RSFT, \
+                           SFT_T(KC_GRV), OS_LALT, OS_LGUI,    TT(_MOUSE),  KC_ENT, \
                                            KC_SPC, BK_LWER,     DL_RAIS \
     )
 

keyboards/bastardkb/charybdis/4x6/keymaps/drashna/rules.mk

@@ -31,3 +31,4 @@ TAP_DANCE_ENABLE      = yes
 DEBOUNCE_TYPE         = asym_eager_defer_pk
 WPM_ENABLE            = yes
 LTO_ENABLE            = no
+# OPT                   = 3

keyboards/bastardkb/dilemma/keymaps/drashna/config.h

@@ -0,0 +1,8 @@
+// Copyright 2020 Christopher Courtney, aka Drashna Jael're  (@drashna) <drashna@live.com>
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#define CIRQUE_PINNACLE_TAP_ENABLE
+#define POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE
+#define POINTING_DEVICE_GESTURES_SCROLL_ENABLE

keyboards/bastardkb/dilemma/keymaps/drashna/keymap.c

@@ -0,0 +1,160 @@
+/**
+ * Copyright 2022 Charly Delay <charly@codesink.dev> (@0xcharly)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "drashna.h"
+
+// clang-format off
+#define LAYOUT_split_3x5_2_wrapper(...) LAYOUT_split_3x5_2(__VA_ARGS__)
+#define LAYOUT_split_3x5_2_base( \
+    K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, \
+    K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \
+    K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A  \
+    ) \
+    LAYOUT_split_3x5_2 ( \
+       K01,    K02,      K03,     K04,     K05,                K06,     K07,     K08,     K09,     K0A, \
+       ALT_T(K11), K12,  K13,     K14,     GUI_T(K15),  LGUI_T(K16),    K17,     K18,     K19, LALT_T(K1A), \
+       CTL_T(K21), K22,  K23,     K24,     K25,                K26,     K27,     K28,     K29, RCTL_T(K2A), \
+                              KC_SPC,  BK_LWER,              DL_RAIS, RSFT_T(KC_ENT) \
+    )
+
+#define LAYOUT_split_3x5_2_base_wrapper(...)       LAYOUT_split_3x5_2_base(__VA_ARGS__)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+    [_DEFAULT_LAYER_1] = LAYOUT_split_3x5_2_base_wrapper(
+        _________________QWERTY_L1_________________, _________________QWERTY_R1_________________,
+        _________________QWERTY_L2_________________, _________________QWERTY_R2_________________,
+        _________________QWERTY_L3_________________, _________________QWERTY_R3_________________
+    ),
+
+    [_DEFAULT_LAYER_2] = LAYOUT_split_3x5_2_base_wrapper(
+        ______________COLEMAK_MOD_DH_L1____________, ______________COLEMAK_MOD_DH_R1____________,
+        ______________COLEMAK_MOD_DH_L2____________, ______________COLEMAK_MOD_DH_R2____________,
+        ______________COLEMAK_MOD_DH_L3____________, ______________COLEMAK_MOD_DH_R3____________
+    ),
+    [_DEFAULT_LAYER_3] = LAYOUT_split_3x5_2_base_wrapper(
+        _________________COLEMAK_L1________________, _________________COLEMAK_R1________________,
+        _________________COLEMAK_L2________________, _________________COLEMAK_R2________________,
+        _________________COLEMAK_L3________________, _________________COLEMAK_R3________________
+    ),
+
+    [_DEFAULT_LAYER_4] = LAYOUT_split_3x5_2_base_wrapper(
+        _________________DVORAK_L1_________________, _________________DVORAK_R1_________________,
+        _________________DVORAK_L2_________________, _________________DVORAK_R2_________________,
+        _________________DVORAK_L3_________________, _________________DVORAK_R3_________________
+    ),
+
+    [_MOUSE] = LAYOUT_split_3x5_2(
+        _______, _______, _______, _______, _______,    KC_WH_U, DPI_RMOD,DPI_MOD, S_D_RMOD,S_D_MOD,
+        _______, _______, _______, _______, _______,    KC_WH_D, KC_BTN1, KC_BTN3, KC_BTN2, KC_BTN6,
+        _______, _______, _______, _______, _______,    KC_BTN7, KC_BTN4, KC_BTN5, KC_BTN8, _______,
+                                    SNIPING, _______,    _______, _______
+    ),
+    [_LOWER] = LAYOUT_split_3x5_2_wrapper(
+        _________________LOWER_L1__________________,    _________________LOWER_R1__________________,
+        _________________LOWER_L2__________________,    _________________LOWER_R2__________________,
+        _________________LOWER_L3__________________,    _________________LOWER_R3__________________,
+                                   _______, _______,    _______, AUTO_CTN
+    ),
+    [_RAISE] = LAYOUT_split_3x5_2_wrapper(
+        _________________RAISE_L1__________________,    _________________RAISE_R1__________________,
+        _________________RAISE_L2__________________,    _________________RAISE_R2__________________,
+        _________________RAISE_L3__________________,    _________________RAISE_R3__________________,
+                                   _______, _______,    _______, _______
+    ),
+    [_ADJUST] = LAYOUT_split_3x5_2_wrapper(
+        _________________ADJUST_L1_________________,    _________________ADJUST_R1_________________,
+        _________________ADJUST_L2_________________,    _________________ADJUST_R2_________________,
+        _________________ADJUST_L3_________________,    _________________ADJUST_R3_________________,
+                                   KC_NUKE, _______,    _______, QK_BOOT
+    ),
+};
+
+
+void matrix_output_unselect_delay(uint8_t line, bool key_pressed) {
+    for (int32_t i = 0; i < 40; i++) {
+        __asm__ volatile("nop" ::: "memory");
+    }
+}
+
+
+#if defined(OLED_ENABLE) && defined(OLED_DISPLAY_128X128)
+#    ifdef UNICODE_COMMON_ENABLE
+#        include "process_unicode_common.h"
+#        include "keyrecords/unicode.h"
+#    endif
+
+extern const char PROGMEM display_border[3];
+
+
+extern uint32_t oled_timer;
+extern bool is_oled_enabled;
+
+
+bool oled_task_keymap(void) {
+    static const char PROGMEM header_image[] = {
+        0, 192, 32, 16, 8, 4, 2, 1, 1, 1, 1, 1, 1, 1, 1, 3, 7, 15, 31, 63, 127, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 127, 63, 31, 15, 7, 3, 1, 1, 1, 1, 1, 1, 1, 1, 2, 4, 8, 16, 32, 192, 0,
+        //         0,255,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  1,  3,  7, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15, 15,  7,  3,  1,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,  0,255,  0
+    };
+    oled_write_raw_P(header_image, sizeof(header_image));
+    oled_set_cursor(7, 0);
+    oled_write_P(PSTR("Rock On"), true);
+
+    render_default_layer_state(1, 1);
+    render_layer_state(1, 2);
+    render_kitty(0, 5);
+    render_wpm(1, 7, 5);
+#   if defined(POINTING_DEVICE_ENABLE)
+    render_pointing_dpi_status(dilemma_get_pointer_sniping_enabled() ? dilemma_get_pointer_sniping_dpi() : dilemma_get_pointer_default_dpi(), 1, 7, 6);
+    render_mouse_mode(17, 6);
+#    elif defined(WPM_ENABLE) && defined(DEBUG_MATRIX_SCAN_RATE)
+    render_matrix_scan_rate(1, 7, 6);
+#    endif
+    render_bootmagic_status(7, 7);
+    render_user_status(1, 9);
+
+    render_mod_status(get_mods() | get_oneshot_mods(), 1, 10);
+    render_keylock_status(host_keyboard_led_state(), 1, 11);
+    render_unicode_mode(1, 12);
+
+//    render_rgb_hsv(1, 13);
+    oled_set_cursor(1, 13);
+    // oled_write_P(PSTR("Timer:"), false);
+    // oled_write(get_u8_str((uint8_t)(timer_elapsed32(oled_timer) / 1000), ' '), false);
+    oled_write_P(PSTR("Status: "), false);
+    if (is_oled_enabled) {
+        oled_write_P(PSTR("on "), false);
+    } else {
+        oled_write_P(PSTR("off"), false);
+    }
+
+    render_keylogger_status(1, 14);
+
+    for (uint8_t i = 1; i < 15; i++) {
+        oled_set_cursor(0, i);
+        oled_write_raw_P(display_border, sizeof(display_border));
+        oled_set_cursor(21, i);
+        oled_write_raw_P(display_border, sizeof(display_border));
+    }
+
+    static const char PROGMEM footer_image[] = {0, 3, 4, 8, 16, 32, 64, 128, 128, 128, 128, 128, 128, 128, 192, 224, 240, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 240, 224, 192, 128, 128, 128, 128, 128, 128, 128, 64, 32, 16, 8, 4, 3, 0};
+    oled_set_cursor(0, 15);
+    oled_write_raw_P(footer_image, sizeof(footer_image));
+
+    return false;
+}
+#endif

keyboards/bastardkb/dilemma/keymaps/drashna/rules.mk

@@ -0,0 +1,8 @@
+SWAP_HANDS_ENABLE     = no
+AUTOCORRECTION_ENABLE = yes
+CAPS_WORD_ENABLE      = yes
+CONSOLE_ENABLE        = yes
+KEYLOGGER_ENABLE      = no
+WPM_ENABLE            = yes
+OLED_ENABLE           = yes
+OLED_DRIVER           = custom

keyboards/handwired/tractyl_manuform/5x6_right/f411/config.h

@@ -75,7 +75,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define I2C1_SCL_PAL_MODE 4
 #define I2C1_SDA_PAL_MODE 4
 #define I2C1_CLOCK_SPEED  400000
-#define I2C1_DUTY_CYCLE FAST_DUTY_CYCLE_2
+#define I2C1_DUTY_CYCLE FAST_DUTY_CYCLE_16_9
 
 /* encoder config */
 #define ENCODERS_PAD_A \

keyboards/handwired/tractyl_manuform/5x6_right/f411/f411.c

@@ -24,7 +24,7 @@ void matrix_scan_sub_kb(void) {
     }
 }
 
-void bootmagic_lite(void) {
+__attribute__((weak)) void bootmagic_lite(void) {
     // We need multiple scans because debouncing can't be turned off.
     matrix_scan();
 #if defined(DEBOUNCE) && DEBOUNCE > 0

keyboards/handwired/tractyl_manuform/5x6_right/keymaps/drashna/config.h

@@ -28,3 +28,9 @@
 #define CHARYBDIS_SNIPING_DPI_CONFIG_STEP 200
 
 #define ENCODER_DEFAULT_POS 0x3
+
+
+#define BOOTMAGIC_LITE_EEPROM_ROW          1
+#define BOOTMAGIC_LITE_EEPROM_COLUMN       0
+#define BOOTMAGIC_LITE_EEPROM_ROW_RIGHT    7
+#define BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT 5

keyboards/ploopyco/mouse/keymaps/drashna/keymap.c

@@ -19,20 +19,23 @@
 
 // safe range starts at `PLOOPY_SAFE_RANGE` instead.
 
+// clang-format off
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    [0] = LAYOUT(/* Base */
+    [0] = LAYOUT(
                  C(KC_C), KC_BTN1, KC_BTN3, KC_BTN2, MO(1), KC_BTN4, KC_BTN5, DPI_CONFIG),
-    [1] = LAYOUT(/* Base */
+    [1] = LAYOUT(
                  RGB_HUI, RGB_MOD, RGB_TOG, RGB_RMOD, MO(1), KC_VOLU, KC_VOLD, QK_BOOT)
-
 };
+// clang-format on
 
+#ifdef RGBLIGHT_ENABLE
 void eeconkfig_init_user(void) {
     rgblight_enable();
-#ifdef RGBLIGHT_EFFECT_TWINKLE
-    rgblight_mode(RGBLIGHT_MODE_TWINKLE+5);
-#else
-    rgblight_mode(RGBLIGHT_MODE_BREATHING+5);
-#endif
+#    ifdef RGBLIGHT_EFFECT_TWINKLE
+    rgblight_mode(RGBLIGHT_MODE_TWINKLE + 5);
+#    else
+    rgblight_mode(RGBLIGHT_MODE_BREATHING + 5);
+#    endif
     rgblight_sethsv(HSV_MAGENTA);
 }
+#endif

keyboards/ploopyco/mouse/keymaps/drashna/rules.mk

@@ -1,5 +1,6 @@
 USER_NAME := not_drashna
+BOOTLOADER = qmk-hid
 
 RGBLIGHT_ENABLE = yes
 CONSOLE_ENABLE  = no
-LTO_ENABLE = yes
+LTO_ENABLE      = yes

keyboards/splitkb/kyria/keymaps/drashna/config.h

@@ -46,4 +46,9 @@
 #define BOOTMAGIC_LITE_ROW_RIGHT    4
 #define BOOTMAGIC_LITE_COLUMN_RIGHT 7
 
+#define BOOTMAGIC_LITE_EEPROM_ROW          1
+#define BOOTMAGIC_LITE_EEPROM_COLUMN       7
+#define BOOTMAGIC_LITE_EEPROM_ROW_RIGHT    5
+#define BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT 7
+
 #define SERIAL_USART_SPEED       921600

users/drashna/autocorrect_data.h

@@ -1,5 +1,93 @@
 #if __has_include("../qmk_secrets/autocorrection_data.h")
+#    pragma message "Loading custom library"
 #    include "../qmk_secrets/autocorrection_data.h"
+#    define AUTOCORRECTION_MIN_LENGTH AUTOCORRECT_MIN_LENGTH
+#    define AUTOCORRECTION_MAX_LENGTH AUTOCORRECT_MAX_LENGTH
+
 #else
-#    include "autocorrect_data_default.h"
+// Generated code.
+
+// Autocorrection dictionary (70 entries):
+//   :guage     -> gauge
+//   :the:the:  -> the
+//   :thier     -> their
+//   :ture      -> true
+//   accomodate -> accommodate
+//   acommodate -> accommodate
+//   aparent    -> apparent
+//   aparrent   -> apparent
+//   apparant   -> apparent
+//   apparrent  -> apparent
+//   aquire     -> acquire
+//   becuase    -> because
+//   cauhgt     -> caught
+//   cheif      -> chief
+//   choosen    -> chosen
+//   cieling    -> ceiling
+//   collegue   -> colleague
+//   concensus  -> consensus
+//   contians   -> contains
+//   cosnt      -> const
+//   dervied    -> derived
+//   fales      -> false
+//   fasle      -> false
+//   fitler     -> filter
+//   flase      -> false
+//   foward     -> forward
+//   frequecy   -> frequency
+//   gaurantee  -> guarantee
+//   guaratee   -> guarantee
+//   heigth     -> height
+//   heirarchy  -> hierarchy
+//   inclued    -> include
+//   interator  -> iterator
+//   intput     -> input
+//   invliad    -> invalid
+//   lenght     -> length
+//   liasion    -> liaison
+//   libary     -> library
+//   listner    -> listener
+//   looses:    -> loses
+//   looup      -> lookup
+//   manefist   -> manifest
+//   namesapce  -> namespace
+//   namespcae  -> namespace
+//   occassion  -> occasion
+//   occured    -> occurred
+//   ouptut     -> output
+//   ouput      -> output
+//   overide    -> override
+//   postion    -> position
+//   priviledge -> privilege
+//   psuedo     -> pseudo
+//   recieve    -> receive
+//   refered    -> referred
+//   relevent   -> relevant
+//   repitition -> repetition
+//   retrun     -> return
+//   retun      -> return
+//   reuslt     -> result
+//   reutrn     -> return
+//   saftey     -> safety
+//   seperate   -> separate
+//   singed     -> signed
+//   stirng     -> string
+//   strign     -> string
+//   swithc     -> switch
+//   swtich     -> switch
+//   thresold   -> threshold
+//   udpate     -> update
+//   widht      -> width
+
+#define AUTOCORRECT_MIN_LENGTH 5  // ":ture"
+#define AUTOCORRECT_MAX_LENGTH 10 // "accomodate"
+
+#define DICTIONARY_SIZE 1104
+
+static const uint8_t autocorrect_data[DICTIONARY_SIZE] PROGMEM = {108, 43,  0,   6,   71, 0,  7,   81, 0,   8,   199, 0,   9,   240, 1,  10,  250, 1,  11,  26,  2,   17,  53,  2,   18, 190, 2,   19,  202, 2,   21,  212, 2,   22,  20,  3,   23,  67,  3,   28,  16,  4,   0,  72,  50,  0,   22,  60,  0,   0,   11,  23,  44, 8,   11, 23,  44,  0,   132, 0,   8,   22,  18,  18,  15,  0,  132, 115, 101, 115, 0,   11,  23,  12,  26,  22,  0,   129, 99,  104, 0,   68,  94,  0,   8,   106, 0,   15, 174, 0,   21, 187, 0,   0,   12,  15,  25,  17,  12,  0,   131, 97,  108, 105, 100, 0,   74,  119, 0,   12,  129, 0,   21,  140, 0,   24,  165, 0,   0,   17,  12,  22,  0,   131, 103, 110, 101, 100, 0,   25,  21, 8,   7,   0,   131, 105, 118, 101, 100, 0,   72,  147, 0,  24,  156, 0,  0,   9,   8,   21,  0,   129, 114, 101, 100, 0,   6,   6,   18,  0,   129, 114, 101, 100, 0,   15,  6,   17,  12,  0,   129, 100, 101, 0,   18, 22,  8,   21,  11,  23,  0,   130, 104, 111,
+                                                                  108, 100, 0,   4,   26, 18, 9,   0,  131, 114, 119, 97,  114, 100, 0,  68,  233, 0,  6,   246, 0,   7,   4,   1,   8,  16,  1,   10,  52,  1,   15,  81,  1,   21,  90,  1,   22,  117, 1,   23,  144, 1,   24, 215, 1,   25,  228, 1,   0,   6,   19,  22,  8,  16,  4,  17,  0,   130, 97,  99,  101, 0,   19,  4,   22,  8,  16,  4,   17,  0,   131, 112, 97,  99,  101, 0,   12,  21,  8,   25,  18,  0,   130, 114, 105, 100, 101, 0,  23,  0,   68, 25,  1,   17,  36,  1,   0,   21,  4,   24,  10,  0,   130, 110, 116, 101, 101, 0,   4,   21,  24,  4,   10,  0,   135, 117, 97,  114, 97,  110, 116, 101, 101, 0,   68,  59,  1,   7,   69,  1,   0,  24,  10,  44,  0,   131, 97,  117, 103, 101, 0,   8,   15, 12,  25,  12, 21,  19,  0,   130, 103, 101, 0,   22,  4,   9,   0,   130, 108, 115, 101, 0,   76,  97,  1,   24,  109, 1,   0,   24,  20,  4,   0,   132, 99, 113, 117, 105, 114, 101, 0,   23,  44,  0,
+                                                                  130, 114, 117, 101, 0,  4,  0,   79, 126, 1,   24,  134, 1,   0,   9,  0,   131, 97, 108, 115, 101, 0,   6,   8,   5,  0,   131, 97,  117, 115, 101, 0,   4,   0,   71,  156, 1,   19,  193, 1,   21,  203, 1,  0,   18,  16,  0,   80,  166, 1,   18,  181, 1,  0,   18, 6,   4,   0,   135, 99,  111, 109, 109, 111, 100, 97, 116, 101, 0,   6,   6,   4,   0,   132, 109, 111, 100, 97,  116, 101, 0,   7,   24,  0,   132, 112, 100, 97, 116, 101, 0,  8,   19,  8,   22,  0,   132, 97,  114, 97,  116, 101, 0,   10,  8,   15,  15,  18,  6,   0,   130, 97,  103, 117, 101, 0,   8,   12,  6,   8,   21,  0,   131, 101, 105, 118, 101, 0,   12,  8,   11, 6,   0,   130, 105, 101, 102, 0,   17,  0,   76,  3,   2,  21,  16,  2,  0,   15,  8,   12,  6,   0,   133, 101, 105, 108, 105, 110, 103, 0,   12,  23,  22,  0,   131, 114, 105, 110, 103, 0,   70,  33,  2,   23,  44, 2,   0,   12,  23,  26,  22,  0,   131, 105,
+                                                                  116, 99,  104, 0,   10, 12, 8,   11, 0,   129, 104, 116, 0,   72,  69, 2,   10,  80, 2,   18,  89,  2,   21,  156, 2,  24,  167, 2,   0,   22,  18,  18,  11,  6,   0,   131, 115, 101, 110, 0,   12,  21,  23, 22,  0,   129, 110, 103, 0,   12,  0,   86,  98, 2,   23, 124, 2,   0,   68,  105, 2,   22,  114, 2,   0,   12, 15,  0,   131, 105, 115, 111, 110, 0,   4,   6,   6,   18,  0,   131, 105, 111, 110, 0,   76,  131, 2,   22, 146, 2,   0,  23,  12,  19,  8,   21,  0,   134, 101, 116, 105, 116, 105, 111, 110, 0,   18,  19,  0,   131, 105, 116, 105, 111, 110, 0,   23,  24,  8,   21,  0,   131, 116, 117, 114, 110, 0,   85,  174, 2,   23, 183, 2,   0,   23,  8,   21,  0,   130, 117, 114, 110, 0,  8,   21,  0,  128, 114, 110, 0,   7,   8,   24,  22,  19,  0,   131, 101, 117, 100, 111, 0,   24,  18,  18,  15,  0,   129, 107, 117, 112, 0,   72,  219, 2,  18,  3,   3,   0,   76,  229, 2,   15,  238,
+                                                                  2,   17,  248, 2,   0,  11, 23,  44, 0,   130, 101, 105, 114, 0,   23, 12,  9,   0,  131, 108, 116, 101, 114, 0,   23, 22,  12,  15,  0,   130, 101, 110, 101, 114, 0,   23,  4,   21,  8,   23,  17,  12,  0,  135, 116, 101, 114, 97,  116, 111, 114, 0,   72, 30,  3,  17,  38,  3,   24,  51,  3,   0,   15,  4,   9,   0,  129, 115, 101, 0,   4,   12,  23,  17,  18,  6,   0,   131, 97,  105, 110, 115, 0,   22,  17,  8,   6,   17, 18,  6,   0,  133, 115, 101, 110, 115, 117, 115, 0,   74,  86,  3,   11,  96,  3,   15,  118, 3,   17,  129, 3,   22,  218, 3,   24,  232, 3,   0,   11,  24,  4,   6,   0,   130, 103, 104, 116, 0,   71,  103, 3,  10,  110, 3,   0,   12,  26,  0,   129, 116, 104, 0,   17, 8,   15,  0,  129, 116, 104, 0,   22,  24,  8,   21,  0,   131, 115, 117, 108, 116, 0,   68,  139, 3,   8,   150, 3,   22,  210, 3,   0,   21,  4,   19,  19, 4,   0,   130, 101, 110, 116, 0,   85,  157,
+                                                                  3,   25,  200, 3,   0,  68, 164, 3,  21,  175, 3,   0,   19,  4,   0,  132, 112, 97, 114, 101, 110, 116, 0,   4,   19, 0,   68,  185, 3,   19,  193, 3,   0,   133, 112, 97,  114, 101, 110, 116, 0,   4,   0,  131, 101, 110, 116, 0,   8,   15,  8,   21,  0,  130, 97, 110, 116, 0,   18,  6,   0,   130, 110, 115, 116, 0,  12,  9,   8,   17,  4,   16,  0,   132, 105, 102, 101, 115, 116, 0,   83,  239, 3,   23,  6,   4,   0,   87, 246, 3,   24, 254, 3,   0,   17,  12,  0,   131, 112, 117, 116, 0,   18,  0,   130, 116, 112, 117, 116, 0,   19,  24,  18,  0,   131, 116, 112, 117, 116, 0,   70,  29,  4,   8,   41,  4,   11,  51,  4,   21,  69, 4,   0,   8,   24,  20,  8,   21,  9,   0,   129, 110, 99, 121, 0,   23, 9,   4,   22,  0,   130, 101, 116, 121, 0,   6,   21,  4,   21,  12,  8,   11,  0,   135, 105, 101, 114, 97,  114, 99,  104, 121, 0,   4,   5,  12,  15,  0,   130, 114, 97,  114, 121, 0};
 #endif

users/drashna/callbacks.c

@@ -3,6 +3,12 @@
 
 #include "drashna.h"
 
+
+#ifdef I2C_SCANNER_ENABLE
+void matrix_scan_i2c(void);
+void keyboard_post_init_i2c(void);
+#endif
+
 __attribute__((weak)) void keyboard_pre_init_keymap(void) {}
 void                       keyboard_pre_init_user(void) {
     userspace_config.raw = eeconfig_read_user();
@@ -42,6 +48,10 @@ void                       keyboard_post_init_user(void) {
 #if defined(SPLIT_KEYBOARD) && defined(SPLIT_TRANSACTION_IDS_USER)
     keyboard_post_init_transport_sync();
 #endif
+#ifdef I2C_SCANNER_ENABLE
+    matrix_scan_i2c();
+#endif
+
     keyboard_post_init_keymap();
 }
 
@@ -54,10 +64,10 @@ void                       shutdown_user(void) {
 #ifdef RGBLIGHT_ENABLE
     rgblight_enable_noeeprom();
     rgblight_mode_noeeprom(1);
-    rgblight_setrgb_red();
+    rgblight_setrgb(rgblight_get_val(), 0x00, 0x00);
 #endif // RGBLIGHT_ENABLE
 #ifdef RGB_MATRIX_ENABLE
-    rgb_matrix_set_color_all(0xFF, 0x00, 0x00);
+    rgb_matrix_set_color_all(rgb_matrix_get_val(), 0x00, 0x00);
     rgb_matrix_update_pwm_buffers();
 #endif // RGB_MATRIX_ENABLE
 #ifdef OLED_ENABLE
@@ -112,6 +122,12 @@ void                       matrix_scan_user(void) {
 #endif
 #if defined(CUSTOM_RGB_MATRIX)
     matrix_scan_rgb_matrix();
+#endif
+#ifdef I2C_SCANNER_ENABLE
+    matrix_scan_i2c();
+#endif
+#ifdef CUSTOM_OLED_DRIVER
+    matrix_scan_oled();
 #endif
     matrix_scan_secret();
 

users/drashna/config.h

@@ -11,26 +11,20 @@
 #endif
 #define IS_COMMAND() (((get_mods() | get_oneshot_mods()) & MOD_MASK_SHIFT) == MOD_MASK_SHIFT)
 
-/* Set Polling rate to 1000Hz */
-#define USB_POLLING_INTERVAL_MS 1
 
 #if defined(SPLIT_KEYBOARD)
-// #    define SPLIT_TRANSPORT_MIRROR
-#    define SPLIT_LAYER_STATE_ENABLE
-#    define SPLIT_LED_STATE_ENABLE
-#    define SPLIT_MODS_ENABLE
-#    ifdef WPM_ENABLE
-#        define SPLIT_WPM_ENABLE
-#    endif
-#    ifdef OLED_ENABLE
-#        define SPLIT_OLED_ENABLE
-#    endif
-#    if defined(__AVR__) && !defined(SELECT_SOFT_SERIAL_SPEED)
-#        define SELECT_SOFT_SERIAL_SPEED 1
-#    endif
-#    ifdef CUSTOM_SPLIT_TRANSPORT_SYNC
-#        define SPLIT_TRANSACTION_IDS_USER RPC_ID_USER_STATE_SYNC, RPC_ID_USER_KEYMAP_SYNC, RPC_ID_USER_CONFIG_SYNC, RPC_ID_USER_WATCHDOG_SYNC, RPC_ID_USER_KEYLOG_STR
-#    endif
+#    include "split/split_config.h"
+#endif
+#ifdef RGBLIGHT_ENABLE
+#    include "rgb/rgblight_config.h"
+#endif // RGBLIGHT_ENABLE
+
+#ifdef RGB_MATRIX_ENABLE
+#    include "rgb/rgb_matrix_config.h"
+#endif // RGB_MATRIX_ENABLE
+
+#ifdef OLED_ENABLE
+#    include "oled/oled_config.h"
 #endif
 
 #if defined(WPM_ENABLE)
@@ -71,157 +65,6 @@
 
 #define UNICODE_SELECTED_MODES UC_WINC, UC_MAC
 
-#ifdef RGBLIGHT_ENABLE
-#    define RGBLIGHT_SLEEP
-#    define RGBLIGHT_EFFECT_TWINKLE_LIFE 250
-#    define RGBLIGHT_EFFECT_TWINKLE_PROBABILITY 1 / 24
-#endif // RGBLIGHT_ENABLE
-
-#ifdef RGB_MATRIX_ENABLE
-#    define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
-// #   define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
-#    define RGB_MATRIX_FRAMEBUFFER_EFFECTS
-// #    define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
-// #    define RGB_DISABLE_WHEN_USB_SUSPENDED // turn off effects when suspended
-
-#    undef ENABLE_RGB_MATRIX_ALPHAS_MODS
-#    undef ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN
-#    undef ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT
-#    undef ENABLE_RGB_MATRIX_BREATHING
-#    undef ENABLE_RGB_MATRIX_BAND_SAT
-#    undef ENABLE_RGB_MATRIX_BAND_VAL
-#    undef ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT
-#    undef ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL
-#    undef ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT
-#    undef ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL
-#    undef ENABLE_RGB_MATRIX_CYCLE_ALL
-#    undef ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT
-#    undef ENABLE_RGB_MATRIX_CYCLE_UP_DOWN
-#    undef ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON
-#    undef ENABLE_RGB_MATRIX_CYCLE_OUT_IN
-#    undef ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL
-#    undef ENABLE_RGB_MATRIX_CYCLE_PINWHEEL
-#    undef ENABLE_RGB_MATRIX_CYCLE_SPIRAL
-#    undef ENABLE_RGB_MATRIX_DUAL_BEACON
-#    undef ENABLE_RGB_MATRIX_RAINBOW_BEACON
-#    undef ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS
-#    undef ENABLE_RGB_MATRIX_RAINDROPS
-#    undef ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
-#    undef ENABLE_RGB_MATRIX_HUE_BREATHING
-#    undef ENABLE_RGB_MATRIX_HUE_PENDULUM
-#    undef ENABLE_RGB_MATRIX_HUE_WAVE
-#    undef ENABLE_RGB_MATRIX_PIXEL_RAIN
-#    undef ENABLE_RGB_MATRIX_PIXEL_FLOW
-#    undef ENABLE_RGB_MATRIX_PIXEL_FRACTAL
-// enabled only if RGB_MATRIX_FRAMEBUFFER_EFFECTS is defined
-#    undef ENABLE_RGB_MATRIX_TYPING_HEATMAP
-#    undef ENABLE_RGB_MATRIX_DIGITAL_RAIN
-// enabled only of RGB_MATRIX_KEYPRESSES or RGB_MATRIX_KEYRELEASES is defined
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS
-#    undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS
-#    undef ENABLE_RGB_MATRIX_SPLASH
-#    undef ENABLE_RGB_MATRIX_MULTISPLASH
-#    undef ENABLE_RGB_MATRIX_SOLID_SPLASH
-#    undef ENABLE_RGB_MATRIX_SOLID_MULTISPLASH
-
-#    define ENABLE_RGB_MATRIX_TYPING_HEATMAP
-#    define ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL
-#    if !defined(SPLIT_KEYBOARD) && !defined(KEYBOARD_ergodox_ez) && !defined(KEYBOARD_moonlander)
-#        define ENABLE_RGB_MATRIX_CYCLE_OUT_IN
-#    endif
-#    if defined(__arm__) || defined(__AVR_AT90USB1286__) || defined(KEYBOARD_launchpad)
-// RGB Matrix Animation modes. Explicitly enabled
-// For full list of effects, see:
-// https://docs.qmk.fm/#/feature_rgb_matrix?id=rgb-matrix-effects
-#        define ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN
-#        define ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT
-#        define ENABLE_RGB_MATRIX_BREATHING
-#        define ENABLE_RGB_MATRIX_BAND_SAT
-#        define ENABLE_RGB_MATRIX_BAND_VAL
-#        define ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT
-#        define ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL
-#        define ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT
-#        define ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL
-#        define ENABLE_RGB_MATRIX_CYCLE_ALL
-#        define ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT
-#        define ENABLE_RGB_MATRIX_CYCLE_UP_DOWN
-#        define ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON
-#        define ENABLE_RGB_MATRIX_CYCLE_OUT_IN
-#        define ENABLE_RGB_MATRIX_CYCLE_PINWHEEL
-#        define ENABLE_RGB_MATRIX_CYCLE_SPIRAL
-#        define ENABLE_RGB_MATRIX_DUAL_BEACON
-#        define ENABLE_RGB_MATRIX_RAINBOW_BEACON
-#        define ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS
-#        define ENABLE_RGB_MATRIX_RAINDROPS
-#        define ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
-#        define ENABLE_RGB_MATRIX_HUE_BREATHING
-#        define ENABLE_RGB_MATRIX_HUE_PENDULUM
-#        define ENABLE_RGB_MATRIX_HUE_WAVE
-#        define ENABLE_RGB_MATRIX_PIXEL_RAIN
-#        define ENABLE_RGB_MATRIX_PIXEL_FLOW
-#        define ENABLE_RGB_MATRIX_PIXEL_FRACTAL
-#        define ENABLE_RGB_MATRIX_DIGITAL_RAIN
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS
-#        define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS
-#        define ENABLE_RGB_MATRIX_SPLASH
-#        define ENABLE_RGB_MATRIX_MULTISPLASH
-#        define ENABLE_RGB_MATRIX_SOLID_SPLASH
-#        define ENABLE_RGB_MATRIX_SOLID_MULTISPLASH
-#    endif // AVR
-#endif     // RGB_MATRIX_ENABLE
-
-#ifdef OLED_ENABLE
-#    ifndef OLED_UPDATE_INTERVAL
-#        ifdef OLED_DRIVER_SH1107
-#            define OLED_UPDATE_INTERVAL 75
-#        else
-#            ifdef SPLIT_KEYBOARD
-#                define OLED_UPDATE_INTERVAL 60
-#            else
-#                define OLED_UPDATE_INTERVAL 15
-#            endif
-#        endif
-#    endif
-#    define OLED_DISABLE_TIMEOUT
-#    ifdef OLED_FONT_H
-#        undef OLED_FONT_H
-#    endif
-#    define OLED_FONT_H "oled/drashna_font.h"
-#    define OLED_FONT_END 255
-// #    define OLED_FONT_5X5
-// #    define OLED_FONT_AZTECH
-// #    define OLED_FONT_BMPLAIN
-// #    define OLED_FONT_CRACKERS
-#    define OLED_FONT_DEAD_MEAL
-// #    define OLED_FONT_EIN
-// #    define OLED_FONT_HISKYF21
-// #    define OLED_FONT_SQUASH
-// #    define OLED_FONT_ZXPIX
-// #    define OLED_FONT_SUPER_DIGG
-
-// #    define OLED_LOGO_BEBOP
-// #    define OLED_LOGO_CORNE
-// #    define OLED_LOGO_GMK_BAD
-// #    define OLED_LOGO_GOTHAM
-// #    define OLED_LOGO_HUE_MANITEE
-// #    define OLED_LOGO_LOOSE
-#    define OLED_LOGO_SCIFI
-// #    define OLED_LOGO_SETS3N
-// #    define OLED_LOGO_SKEEB
-#endif
-
 // #define WPM_ESTIMATED_WORD_SIZE 5
 #define WPM_ALLOW_COUNT_REGRESSION
 // #define WPM_UNFILTERED
@@ -237,11 +80,18 @@
 #    define ONESHOT_TIMEOUT 3000
 #endif // !ONESHOT_TIMEOUT
 
-#define IGNORE_MOD_TAP_INTERRUPT_PER_KEY
-#define PERMISSIVE_HOLD_PER_KEY
-#define TAPPING_FORCE_HOLD_PER_KEY
-#define RETRO_TAPPING_PER_KEY
-#define TAPPING_TERM_PER_KEY
+#if defined(PER_KEY_TAPPING)
+#    define IGNORE_MOD_TAP_INTERRUPT_PER_KEY
+#    define PERMISSIVE_HOLD_PER_KEY
+#    define TAPPING_FORCE_HOLD_PER_KEY
+#    define HOLD_ON_OTHER_KEY
+#    define RETRO_TAPPING_PER_KEY
+#    define HOLD_ON_OTHER_KEY_PRESS_PER_KEY
+#    define TAPPING_TERM_PER_KEY
+#else
+#    define IGNORE_MOD_TAP_INTERRUPT
+#    undef PERMISSIVE_HOLD
+#endif
 
 #ifndef TAPPING_TOGGLE
 #    define TAPPING_TOGGLE 1
@@ -276,41 +126,7 @@
 #    define C15 PAL_LINE(GPIOC, 15)
 #endif
 
-#ifdef OLED_DRIVER_SH1107
-#    define OLED_DISPLAY_CUSTOM
-#    define OLED_IC_SH1107 2
-#    define OLED_DISPLAY_128X128
-#    define OLED_DISPLAY_WIDTH 128
-#    define OLED_DISPLAY_HEIGHT 128
-#    define OLED_MATRIX_SIZE (OLED_DISPLAY_HEIGHT / 8 * OLED_DISPLAY_WIDTH)
-#    define OLED_BLOCK_TYPE uint32_t
-#    define OLED_SOURCE_MAP \
-        { 0, 8, 16, 24, 32, 40, 48, 56 }
-#    define OLED_TARGET_MAP \
-        { 56, 48, 40, 32, 24, 16, 8, 0 }
-#    define OLED_BLOCK_COUNT (sizeof(OLED_BLOCK_TYPE) * 8)
-#    define OLED_BLOCK_SIZE (OLED_MATRIX_SIZE / OLED_BLOCK_COUNT)
-#    define OLED_COM_PINS COM_PINS_ALT
-#    define OLED_IC OLED_IC_SH1107
-#    ifndef OLED_BRIGHTNESS
-#        define OLED_BRIGHTNESS 50
-#    endif
-#endif
-
-#ifdef USE_I2CV1
-#    define I2C1_CLOCK_SPEED 400000
-#    define I2C1_DUTY_CYCLE FAST_DUTY_CYCLE_2
-#endif
 
 #define ENABLE_COMPILE_KEYCODE
 
 #define BOTH_SHIFTS_TURNS_ON_CAPS_WORD
-
-#ifndef SECURE_UNLOCK_SEQUENCE
-#    define SECURE_UNLOCK_SEQUENCE    \
-        {                             \
-            {2, 1}, {2, 2}, {2, 3}, { \
-                2, 4                  \
-            }                         \
-        }
-#endif

users/drashna/drashna.c

@@ -76,49 +76,110 @@ void tap_code16_nomods(uint16_t kc) {
     set_mods(temp_mod);
 }
 
-/**
- * @brief Run shutdown routine and soft reboot firmware.
- *
- */
-
-#ifdef HAPTIC_ENABLE
-#    include "haptic.h"
-#endif
+#ifdef I2C_SCANNER_ENABLE
+#    include "i2c_master.h"
+#    include "debug.h"
 
-#ifdef AUDIO_ENABLE
-#    ifndef GOODBYE_SONG
-#        define GOODBYE_SONG SONG(GOODBYE_SOUND)
+#    ifndef I2C_SCANNER_TIMEOUT
+#        define I2C_SCANNER_TIMEOUT 50
 #    endif
-float reset_song[][2] = GOODBYE_SONG;
-#endif
 
-void software_reset(void) {
-    clear_keyboard();
-#if defined(MIDI_ENABLE) && defined(MIDI_BASIC)
-    process_midi_all_notes_off();
+i2c_status_t i2c_start_bodge(uint8_t address, uint16_t timeout) {
+    i2c_start(address);
+
+    // except on ChibiOS where the only way is do do "something"
+    uint8_t data = 0;
+    return i2c_readReg(address, 0, &data, sizeof(data), I2C_SCANNER_TIMEOUT);
+}
+
+#    define i2c_start i2c_start_bodge
+
+void do_scan(void) {
+    uint8_t nDevices = 0;
+
+    dprintf("Scanning...\n");
+
+    for (uint8_t address = 1; address < 127; address++) {
+        // The i2c_scanner uses the return value of
+        // i2c_start to see if a device did acknowledge to the address.
+        i2c_status_t error = i2c_start(address << 1, I2C_SCANNER_TIMEOUT);
+        if (error == I2C_STATUS_SUCCESS) {
+            i2c_stop();
+            xprintf("  I2C device found at address 0x%02X\n", I2C_SCANNER_TIMEOUT);
+            nDevices++;
+        } else {
+            // dprintf("  Unknown error (%u) at address 0x%02X\n", error, address);
+        }
+    }
+
+    if (nDevices == 0)
+        xprintf("No I2C devices found\n");
+    else
+        xprintf("done\n");
+}
+
+uint16_t scan_timer = 0;
+
+void matrix_scan_i2c(void) {
+    if (timer_elapsed(scan_timer) > 5000) {
+        do_scan();
+        scan_timer = timer_read();
+    }
+}
+
+void keyboard_post_init_i2c(void) {
+    i2c_init();
+    scan_timer = timer_read();
+}
 #endif
-#ifdef AUDIO_ENABLE
-#    ifndef NO_MUSIC_MODE
-    music_all_notes_off();
-#    endif
-    uint16_t timer_start = timer_read();
-    PLAY_SONG(reset_song);
-    shutdown_user();
-    while (timer_elapsed(timer_start) < 250) wait_ms(1);
-    stop_all_notes();
+
+void bootmagic_lite(void) {
+    bool perform_reset = false;
+    // We need multiple scans because debouncing can't be turned off.
+    matrix_scan();
+#if defined(DEBOUNCE) && DEBOUNCE > 0
+    wait_ms(DEBOUNCE * 2);
 #else
-    shutdown_user();
-    wait_ms(250);
+    wait_ms(30);
 #endif
-#ifdef HAPTIC_ENABLE
-    haptic_shutdown();
+    matrix_scan();
+
+    // If the configured key (commonly Esc) is held down on power up,
+    // reset the EEPROM valid state and jump to bootloader.
+    // This isn't very generalized, but we need something that doesn't
+    // rely on user's keymaps in firmware or EEPROM.
+    uint8_t row = BOOTMAGIC_LITE_ROW, col = BOOTMAGIC_LITE_COLUMN;
+#if defined(BOOTMAGIC_LITE_EEPROM_ROW) && defined(BOOTMAGIC_LITE_EEPROM_COLUMN)
+    uint8_t row_e = BOOTMAGIC_LITE_EEPROM_ROW, col_e = BOOTMAGIC_LITE_EEPROM_COLUMN;
 #endif
 
-#if defined(PROTOCOL_LUFA)
-    wdt_enable(WDTO_250MS);
-#elif defined(PROTOCOL_CHIBIOS)
-#    if defined(MCU_STM32) || defined(MCU_KINETIS)
-    NVIC_SystemReset();
+#if defined(SPLIT_KEYBOARD) && defined(BOOTMAGIC_LITE_ROW_RIGHT) && defined(BOOTMAGIC_LITE_COLUMN_RIGHT)
+    if (!is_keyboard_left()) {
+        row = BOOTMAGIC_LITE_ROW_RIGHT;
+        col = BOOTMAGIC_LITE_COLUMN_RIGHT;
+#if defined(BOOTMAGIC_LITE_EEPROM_ROW) && defined(BOOTMAGIC_LITE_EEPROM_COLUMN) && defined(BOOTMAGIC_LITE_EEPROM_ROW_RIGHT) && defined(BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT)
+        row_e = BOOTMAGIC_LITE_EEPROM_ROW_RIGHT;
+        col_e = BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT;
 #    endif
+    }
 #endif
+
+#if defined(BOOTMAGIC_LITE_EEPROM_ROW) && defined(BOOTMAGIC_LITE_EEPROM_COLUMN)
+    if (matrix_get_row(row_e) & (1 << col_e)) {
+        eeconfig_disable();
+        perform_reset = true;
+    }
+#endif
+    if (matrix_get_row(row) & (1 << col)) {
+        perform_reset = true;
+    }
+#ifdef STM32F411xE
+    if (!readPin(A0)) {
+        perform_reset = true;
+    }
+#endif
+
+    if (perform_reset) {
+        bootloader_jump();
+    }
 }

users/drashna/drashna.h

@@ -79,7 +79,6 @@ bool mod_key_press_timer(uint16_t code, uint16_t mod_code, bool pressed);
 bool mod_key_press(uint16_t code, uint16_t mod_code, bool pressed, uint16_t this_timer);
 bool hasAllBitsInMask(uint8_t value, uint8_t mask);
 void tap_code16_nomods(uint16_t kc);
-void software_reset(void);
 
 // clang-format off
 typedef union {

users/drashna/keyrecords/autocorrection/autocorrection_data.h

@@ -0,0 +1 @@
+#include "autocorrect_data.h"

users/drashna/keyrecords/process_records.c

@@ -6,9 +6,6 @@
 #ifdef AUTOCORRECTION_ENABLE
 #    include "autocorrection/autocorrection.h"
 #endif
-#ifdef __AVR__
-#    include <avr/wdt.h>
-#endif
 
 uint16_t copy_paste_timer;
 bool     host_driver_disabled = false;
@@ -49,7 +46,7 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
 #endif
     // If console is enabled, it will print the matrix position and status of each key pressed
 #ifdef KEYLOGGER_ENABLE
-    uprintf("KL: kc: 0x%04X, col: %2u, row: %2u, pressed: %b, time: %5u, int: %b, count: %u\n", keycode, record->event.key.col, record->event.key.row, record->event.pressed, record->event.time, record->tap.interrupted, record->tap.count);
+    uprintf("KL: kc: 0x%04X, col: %2u, row: %2u, pressed: %1d, time: %5u, int: %1d, count: %u\n", keycode, record->event.key.col, record->event.key.row, record->event.pressed, record->event.time, record->tap.interrupted, record->tap.count);
 #endif // KEYLOGGER_ENABLE
 #if defined(OLED_ENABLE) && defined(CUSTOM_OLED_DRIVER)
     process_record_user_oled(keycode, record);

users/drashna/keyrecords/tapping.c

@@ -3,6 +3,7 @@
 
 #include "drashna.h"
 
+#ifdef TAPPING_TERM_PER_KEY
 __attribute__((weak)) uint16_t get_tapping_term(uint16_t keycode, keyrecord_t *record) {
     switch (keycode) {
         case BK_LWER:
@@ -11,7 +12,9 @@ __attribute__((weak)) uint16_t get_tapping_term(uint16_t keycode, keyrecord_t *r
             return TAPPING_TERM;
     }
 }
+#endif // TAPPING_TERM_PER_KEY
 
+#ifdef PERMISSIVE_HOLD_PER_KEY
 __attribute__((weak)) bool get_permissive_hold(uint16_t keycode, keyrecord_t *record) {
     // Immediately select the hold action when another key is tapped:
     // return true;
@@ -22,7 +25,9 @@ __attribute__((weak)) bool get_permissive_hold(uint16_t keycode, keyrecord_t *re
             return false;
     }
 }
+#endif // PERMISSIVE_HOLD_PER_KEY
 
+#ifdef HOLD_ON_OTHER_KEY_PRESS_PER_KEY
 __attribute__((weak)) bool get_hold_on_other_key_press(uint16_t keycode, keyrecord_t *record) {
     // Immediately select the hold action when another key is pressed.
     // return true;
@@ -32,10 +37,12 @@ __attribute__((weak)) bool get_hold_on_other_key_press(uint16_t keycode, keyreco
 //        case QK_LAYER_TAP ... QK_LAYER_TAP_MAX:
 //            return true;
         default:
-            return true;
+            return false;
     }
 }
+#endif // HOLD_ON_OTHER_KEY_PRESS_PER_KEY
 
+#ifdef IGNORE_MOD_TAP_INTERRUPT_PER_KEY
 __attribute__((weak)) bool get_ignore_mod_tap_interrupt(uint16_t keycode, keyrecord_t *record) {
     // Do not force the mod-tap key press to be handled as a modifier
     // if any other key was pressed while the mod-tap key is held down.
@@ -48,17 +55,22 @@ __attribute__((weak)) bool get_ignore_mod_tap_interrupt(uint16_t keycode, keyrec
             return true;
     }
 }
+#endif // IGNORE_MOD_TAP_INTERRUPT_PER_KEY
 
+#ifdef TAPPING_FORCE_HOLD_PER_KEY
 __attribute__((weak)) bool get_tapping_force_hold(uint16_t keycode, keyrecord_t *record) {
     switch (keycode) {
         default:
             return false;
     }
 }
+#endif // TAPPING_FORCE_HOLD_PER_KEY
 
+#ifdef RETRO_TAPPING_PER_KEY
 __attribute__((weak)) bool get_retro_tapping(uint16_t keycode, keyrecord_t *record) {
     switch (keycode) {
         default:
             return false;
     }
 }
+#endif // RETRO_TAPPING_PER_KEY

users/drashna/keyrecords/unicode.c

@@ -142,7 +142,7 @@ DEFINE_UNICODE_LUT_TRANSLATOR(unicode_lut_translator_super,
                               0x2071, // i
                               0x02B2, // j
                               0x1D4F, // k
-                              0x1D4F, // l
+                              0x02E1, // l
                               0x1D50, // m
                               0x207F, // n
                               0x1D52, // o

users/drashna/oled/oled_config.h

@@ -0,0 +1,63 @@
+// Copyright 2020 Christopher Courtney, aka Drashna Jael're  (@drashna) <drashna@live.com>
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#ifndef OLED_UPDATE_INTERVAL
+#    ifdef OLED_DRIVER_SH1107
+#        define OLED_UPDATE_INTERVAL 75
+#    else
+#        ifdef SPLIT_KEYBOARD
+#            define OLED_UPDATE_INTERVAL 60
+#        else
+#            define OLED_UPDATE_INTERVAL 15
+#        endif
+#    endif
+#endif
+#define OLED_DISABLE_TIMEOUT
+#ifdef OLED_FONT_H
+#    undef OLED_FONT_H
+#endif
+#define OLED_FONT_H "oled/drashna_font.h"
+#define OLED_FONT_END 255
+// #    define OLED_FONT_5X5
+// #    define OLED_FONT_AZTECH
+// #    define OLED_FONT_BMPLAIN
+// #    define OLED_FONT_CRACKERS
+#define OLED_FONT_DEAD_MEAL
+// #    define OLED_FONT_EIN
+// #    define OLED_FONT_HISKYF21
+// #    define OLED_FONT_SQUASH
+// #    define OLED_FONT_ZXPIX
+// #    define OLED_FONT_SUPER_DIGG
+
+// #    define OLED_LOGO_BEBOP
+// #    define OLED_LOGO_CORNE
+// #    define OLED_LOGO_GMK_BAD
+// #    define OLED_LOGO_GOTHAM
+// #    define OLED_LOGO_HUE_MANITEE
+// #    define OLED_LOGO_LOOSE
+#define OLED_LOGO_SCIFI
+// #    define OLED_LOGO_SETS3N
+// #    define OLED_LOGO_SKEEB
+
+#ifdef OLED_DRIVER_SH1107
+#    define OLED_DISPLAY_CUSTOM
+#    define OLED_IC_SH1107 2
+#    define OLED_DISPLAY_128X128
+#    define OLED_DISPLAY_WIDTH 128
+#    define OLED_DISPLAY_HEIGHT 128
+#    define OLED_MATRIX_SIZE (OLED_DISPLAY_HEIGHT / 8 * OLED_DISPLAY_WIDTH)
+#    define OLED_BLOCK_TYPE uint32_t
+#    define OLED_SOURCE_MAP \
+        { 0, 8, 16, 24, 32, 40, 48, 56 }
+#    define OLED_TARGET_MAP \
+        { 56, 48, 40, 32, 24, 16, 8, 0 }
+#    define OLED_BLOCK_COUNT (sizeof(OLED_BLOCK_TYPE) * 8)
+#    define OLED_BLOCK_SIZE (OLED_MATRIX_SIZE / OLED_BLOCK_COUNT)
+#    define OLED_COM_PINS COM_PINS_ALT
+#    define OLED_IC OLED_IC_SH1107
+#    ifndef OLED_BRIGHTNESS
+#        define OLED_BRIGHTNESS 50
+#    endif
+#endif

users/drashna/oled/oled_stuff.c

@@ -28,6 +28,8 @@
 #endif
 #include <string.h>
 
+bool is_oled_enabled = true;
+
 extern bool host_driver_disabled;
 
 uint32_t        oled_timer                        = 0;
@@ -850,7 +852,7 @@ void render_status_right(void) {
     render_layer_state(1, 2);
     render_mod_status(get_mods() | get_oneshot_mods(), 1, 5);
 #if !defined(OLED_DISPLAY_VERBOSE) && defined(WPM_ENABLE) && !defined(STM32F303xC)
-    render_wpm(2);
+    render_wpm(2, 7, 1);
 #endif
     render_keylock_status(host_keyboard_led_state(), 1, 6);
 }
@@ -929,16 +931,14 @@ __attribute__((weak)) bool oled_task_keymap(void) {
 }
 
 bool oled_task_user(void) {
-    if (is_keyboard_master()) {
 #ifndef OLED_DISPLAY_TEST
-        if (timer_elapsed32(oled_timer) > 60000) {
-            oled_off();
-            return false;
-        } else
+    if (!is_oled_enabled) {
+        oled_off();
+        return false;
+    } else
 #endif
-        {
-            oled_on();
-        }
+    {
+        oled_on();
     }
 
     if (!oled_task_keymap()) {
@@ -990,3 +990,9 @@ bool oled_task_user(void) {
 
     return false;
 }
+
+extern bool oled_initialized;
+
+__attribute__((weak)) void matrix_scan_oled(void) {
+    is_oled_enabled = !(timer_elapsed32(oled_timer) > 60000);
+}

users/drashna/oled/oled_stuff.h

@@ -44,6 +44,8 @@ void            render_wpm_graph(uint8_t max_lines_graph, uint8_t vertical_offse
 void            render_kitty(uint8_t col, uint8_t line);
 void            render_unicode_mode(uint8_t col, uint8_t line);
 void            render_rgb_hsv(uint8_t col, uint8_t line);
+void            render_mouse_mode(uint8_t col, uint8_t line);
+void            matrix_scan_oled(void);
 
 void oled_pan_section(bool left, uint16_t y_start, uint16_t y_end, uint16_t x_start, uint16_t x_end);
 

users/drashna/pointing/pointing.c

@@ -22,7 +22,7 @@ __attribute__((weak)) report_mouse_t pointing_device_task_keymap(report_mouse_t
 }
 
 report_mouse_t pointing_device_task_user(report_mouse_t mouse_report) {
-    int8_t x = mouse_report.x, y = mouse_report.y;
+    mouse_xy_report_t x = mouse_report.x, y = mouse_report.y;
     mouse_report.x = 0;
     mouse_report.y = 0;
 
@@ -33,8 +33,8 @@ report_mouse_t pointing_device_task_user(report_mouse_t mouse_report) {
 #endif
         if (timer_elapsed(mouse_debounce_timer) > TAP_CHECK) {
             if (enable_acceleration) {
-                x = (x > 0 ? x * x / 16 + x : -x * x / 16 + x);
-                y = (y > 0 ? y * y / 16 + y : -y * y / 16 + y);
+                x = (mouse_xy_report_t)(x > 0 ? x * x / 16 + x : -x * x / 16 + x);
+                y = (mouse_xy_report_t)(y > 0 ? y * y / 16 + y : -y * y / 16 + y);
             }
             mouse_report.x = x;
             mouse_report.y = y;

users/drashna/post_config.h

@@ -113,13 +113,17 @@
 #    endif
 #endif  // MOUSEKEY_ENABLE
 
-#if !defined(LAYER_STATE_16BIT) && !defined(LAYER_STATE_8BIT) && !defined(LAYER_STATE_32BIT)
-#    define LAYER_STATE_16BIT
-#endif
-#ifndef DYNAMIC_KEYMAP_LAYER_COUNT
-#    define DYNAMIC_KEYMAP_LAYER_COUNT 11
-#endif
+#define MOUSE_EXTENDED_REPORT
 
 #ifndef TAPPING_TERM
 #    define TAPPING_TERM 175
 #endif
+
+#ifndef SECURE_UNLOCK_SEQUENCE
+#    define SECURE_UNLOCK_SEQUENCE    \
+        {                             \
+            {2, 1}, {2, 2}, {2, 3}, { \
+                2, 4                  \
+            }                         \
+        }
+#endif

users/drashna/rgb/rgb_matrix_config.h

@@ -0,0 +1,107 @@
+// Copyright 2020 Christopher Courtney, aka Drashna Jael're  (@drashna) <drashna@live.com>
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
+// #   define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
+#define RGB_MATRIX_FRAMEBUFFER_EFFECTS
+// #    define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
+// #    define RGB_DISABLE_WHEN_USB_SUSPENDED // turn off effects when suspended
+
+#undef ENABLE_RGB_MATRIX_ALPHAS_MODS
+#undef ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN
+#undef ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT
+#undef ENABLE_RGB_MATRIX_BREATHING
+#undef ENABLE_RGB_MATRIX_BAND_SAT
+#undef ENABLE_RGB_MATRIX_BAND_VAL
+#undef ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT
+#undef ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL
+#undef ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT
+#undef ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL
+#undef ENABLE_RGB_MATRIX_CYCLE_ALL
+#undef ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT
+#undef ENABLE_RGB_MATRIX_CYCLE_UP_DOWN
+#undef ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON
+#undef ENABLE_RGB_MATRIX_CYCLE_OUT_IN
+#undef ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL
+#undef ENABLE_RGB_MATRIX_CYCLE_PINWHEEL
+#undef ENABLE_RGB_MATRIX_CYCLE_SPIRAL
+#undef ENABLE_RGB_MATRIX_DUAL_BEACON
+#undef ENABLE_RGB_MATRIX_RAINBOW_BEACON
+#undef ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS
+#undef ENABLE_RGB_MATRIX_RAINDROPS
+#undef ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
+#undef ENABLE_RGB_MATRIX_HUE_BREATHING
+#undef ENABLE_RGB_MATRIX_HUE_PENDULUM
+#undef ENABLE_RGB_MATRIX_HUE_WAVE
+#undef ENABLE_RGB_MATRIX_PIXEL_RAIN
+#undef ENABLE_RGB_MATRIX_PIXEL_FLOW
+#undef ENABLE_RGB_MATRIX_PIXEL_FRACTAL
+// enabled only if RGB_MATRIX_FRAMEBUFFER_EFFECTS is defined
+#undef ENABLE_RGB_MATRIX_TYPING_HEATMAP
+#undef ENABLE_RGB_MATRIX_DIGITAL_RAIN
+// enabled only of RGB_MATRIX_KEYPRESSES or RGB_MATRIX_KEYRELEASES is defined
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS
+#undef ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS
+#undef ENABLE_RGB_MATRIX_SPLASH
+#undef ENABLE_RGB_MATRIX_MULTISPLASH
+#undef ENABLE_RGB_MATRIX_SOLID_SPLASH
+#undef ENABLE_RGB_MATRIX_SOLID_MULTISPLASH
+
+#define ENABLE_RGB_MATRIX_TYPING_HEATMAP
+#define ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL
+#if !defined(SPLIT_KEYBOARD) && !defined(KEYBOARD_ergodox_ez) && !defined(KEYBOARD_moonlander)
+#    define ENABLE_RGB_MATRIX_CYCLE_OUT_IN
+#endif
+#if defined(__arm__) || defined(__AVR_AT90USB1286__) || defined(KEYBOARD_launchpad)
+// RGB Matrix Animation modes. Explicitly enabled
+// For full list of effects, see:
+// https://docs.qmk.fm/#/feature_rgb_matrix?id=rgb-matrix-effects
+#    define ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN
+#    define ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT
+#    define ENABLE_RGB_MATRIX_BREATHING
+#    define ENABLE_RGB_MATRIX_BAND_SAT
+#    define ENABLE_RGB_MATRIX_BAND_VAL
+#    define ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT
+#    define ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL
+#    define ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT
+#    define ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL
+#    define ENABLE_RGB_MATRIX_CYCLE_ALL
+#    define ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT
+#    define ENABLE_RGB_MATRIX_CYCLE_UP_DOWN
+#    define ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON
+#    define ENABLE_RGB_MATRIX_CYCLE_OUT_IN
+#    define ENABLE_RGB_MATRIX_CYCLE_PINWHEEL
+#    define ENABLE_RGB_MATRIX_CYCLE_SPIRAL
+#    define ENABLE_RGB_MATRIX_DUAL_BEACON
+#    define ENABLE_RGB_MATRIX_RAINBOW_BEACON
+#    define ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS
+#    define ENABLE_RGB_MATRIX_RAINDROPS
+#    define ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
+#    define ENABLE_RGB_MATRIX_HUE_BREATHING
+#    define ENABLE_RGB_MATRIX_HUE_PENDULUM
+#    define ENABLE_RGB_MATRIX_HUE_WAVE
+#    define ENABLE_RGB_MATRIX_PIXEL_RAIN
+#    define ENABLE_RGB_MATRIX_PIXEL_FLOW
+#    define ENABLE_RGB_MATRIX_PIXEL_FRACTAL
+#    define ENABLE_RGB_MATRIX_DIGITAL_RAIN
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS
+#    define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS
+#    define ENABLE_RGB_MATRIX_SPLASH
+#    define ENABLE_RGB_MATRIX_MULTISPLASH
+#    define ENABLE_RGB_MATRIX_SOLID_SPLASH
+#    define ENABLE_RGB_MATRIX_SOLID_MULTISPLASH
+#endif // AVR

users/drashna/rgb/rgblight_config.h

@@ -0,0 +1,8 @@
+// Copyright 2020 Christopher Courtney, aka Drashna Jael're  (@drashna) <drashna@live.com>
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#    define RGBLIGHT_SLEEP
+#    define RGBLIGHT_EFFECT_TWINKLE_LIFE 250
+#    define RGBLIGHT_EFFECT_TWINKLE_PROBABILITY 1 / 24

users/drashna/rules.mk

@@ -36,6 +36,10 @@ ifeq ($(strip $(PROTOCOL)), VUSB)
     NKRO_ENABLE       := no
 endif
 
+ifeq ($(strip $(PER_KEY_TAPPING)), yes)
+    OPT_DEFS += -DPER_KEY_TAPPING
+endif
+
 CUSTOM_UNICODE_ENABLE ?= yes
 ifeq ($(strip $(CUSTOM_UNICODE_ENABLE)), yes)
     UNICODE_ENABLE        := no
@@ -83,6 +87,11 @@ ifdef CONSOLE_ENABLE
     endif
 endif
 
+ifeq ($(strip $(I2C_SCANNER_ENABLE)), yes)
+    OPT_DEFS += -DI2C_SCANNER_ENABLE
+    CONSOLE_ENABLE := yes
+endif
+
 CUSTOM_OLED_DRIVER ?= yes
 ifeq ($(strip $(OLED_ENABLE)), yes)
     ifeq ($(strip $(OLED_DRIVER)), custom)

users/drashna/split/split_config.h

@@ -0,0 +1,21 @@
+// Copyright 2020 Christopher Courtney, aka Drashna Jael're  (@drashna) <drashna@live.com>
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+// #    define SPLIT_TRANSPORT_MIRROR
+#define SPLIT_LAYER_STATE_ENABLE
+#define SPLIT_LED_STATE_ENABLE
+#define SPLIT_MODS_ENABLE
+#ifdef WPM_ENABLE
+#    define SPLIT_WPM_ENABLE
+#endif
+#ifdef OLED_ENABLE
+#    undef SPLIT_OLED_ENABLE
+#endif
+#if defined(__AVR__) && !defined(SELECT_SOFT_SERIAL_SPEED)
+#    define SELECT_SOFT_SERIAL_SPEED 1
+#endif
+#ifdef CUSTOM_SPLIT_TRANSPORT_SYNC
+#    define SPLIT_TRANSACTION_IDS_USER RPC_ID_USER_STATE_SYNC, RPC_ID_USER_KEYMAP_SYNC, RPC_ID_USER_CONFIG_SYNC, RPC_ID_USER_WATCHDOG_SYNC, RPC_ID_USER_KEYLOG_STR
+#endif

users/drashna/split/transport_sync.c

@@ -4,9 +4,6 @@
 #include "transport_sync.h"
 #include "transactions.h"
 #include <string.h>
-#ifdef __AVR__
-#    include <avr/wdt.h>
-#endif
 
 #ifdef UNICODE_COMMON_ENABLE
 #    include "process_unicode_common.h"
@@ -18,6 +15,9 @@ extern unicode_config_t unicode_config;
 extern audio_config_t audio_config;
 extern bool           delayed_tasks_run;
 #endif
+#if defined(OLED_ENABLE) && !defined(SPLIT_OLED_ENABLE) && defined(CUSTOM_OLED_DRIVER)
+extern bool is_oled_enabled;
+#endif
 #if defined(POINTING_DEVICE_ENABLE) && defined(KEYBOARD_handwired_tractyl_manuform)
 extern bool tap_toggling;
 #endif
@@ -95,6 +95,9 @@ void user_transport_update(void) {
         user_state.audio_enable        = is_audio_on();
         user_state.audio_clicky_enable = is_clicky_on();
 #endif
+#if defined(OLED_ENABLE) && !defined(SPLIT_OLED_ENABLE) && defined(CUSTOM_OLED_DRIVER)
+        user_state.is_oled_enabled = is_oled_enabled;
+#endif
 #if defined(CUSTOM_POINTING_DEVICE)
         user_state.tap_toggling = tap_toggling;
 #endif
@@ -116,6 +119,9 @@ void user_transport_update(void) {
         unicode_config.input_mode = user_state.unicode_mode;
         typing_mode               = user_state.unicode_typing_mode;
 #endif
+#if defined(OLED_ENABLE) && !defined(SPLIT_OLED_ENABLE) && defined(CUSTOM_OLED_DRIVER)
+        is_oled_enabled = user_state.is_oled_enabled;
+#endif
 #if defined(CUSTOM_POINTING_DEVICE)
         tap_toggling = user_state.tap_toggling;
 #endif
@@ -226,7 +232,7 @@ void user_transport_sync(void) {
             }
         } else {
             if (timer_elapsed32(watchdog_timer) > 3500) {
-                software_reset();
+                mcu_reset();
                 while (1) {
                 }
             }

users/drashna/split/transport_sync.h

@@ -19,6 +19,7 @@ typedef union {
         bool    swap_hands           :1;
         bool    host_driver_disabled :1;
         uint8_t unicode_typing_mode  :3;
+        bool    is_oled_enabled      :1;
     };
 } user_runtime_config_t;