[Keyboard] Move more percent boards into the percent directory (#6781)

* move canoe into percent directory

* update readme for new make path

* move skog into percent directory

* update readme for new path and new instructions

* update readme

* fix error in naming

keyboards/canoe/readme.md → keyboards/percent/canoe/readme.md

@@ -1,5 +1,4 @@
-CANOE
-========
+# Canoe
 
 A 65% keyboard with some RGB
 
@@ -9,7 +8,7 @@ Hardware Availability: https://geekhack.org/index.php?topic=92418.0
 
 Make example for this keyboard (after setting up your build environment):
 
-    make canoe:default
+    make percent/canoe:default
 
 Flashing
 
@@ -33,12 +32,13 @@ macOS:
     ```
 3. Install the following packages:
     ```
-    brew install python
-    pip install pyusb
+    brew install python3
+    pip3 install pyusb
     brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
 
 4. Place your keyboard into reset. 
 5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
 
 
-See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/skog/README.md → keyboards/percent/skog/README.md

@@ -1,5 +1,4 @@
-Skog TKL by Percent
-==========================
+# Skog TKL
 
 Keyboard Maintainer: QMK Community  
 Hardware Supported: Skog PCB  
@@ -7,21 +6,14 @@ Hardware Availability: https://geekhack.org/index.php?topic=87953.0
 
 Make example for this keyboard (after setting up your build environment):
 
-    make skog:default
+    make percent/skog:default
 
-## Setting the board to bootloader mode
-
-If you're lucky, the programming script does this automagically for you. If
-however this doesn't work for you, you need to enter the bootloader mode manually
-by plugging the keyboard in while holding the bootloader key. If you did this
-correctly the LEDs will blink and you'll be able to flash your firmware.
-
-The bootloader key is in the top-right (Pause).
-
-## Flashing
+Flashing
 
 ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
 
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as Pause while plugging in the keyboard.
+
 Windows: 
 1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
 2. Place your keyboard into reset. 
@@ -40,22 +32,14 @@ macOS:
     ```
 3. Install the following packages:
     ```
-    brew install python
-    brew install pyusb
-    brew install --HEAD`https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    brew install python3
+    pip3 install pyusb
+    brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
 
 4. Place your keyboard into reset. 
 5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
 
-See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
-
-## Troubleshooting
-
-From my experience, it's really hard to brick these boards. But these
-tricks have been useful when it got stuck in a weird scenario.
+**Please Note:** You will need to use the `EEP_RST` keycode first, followed by unplugging/replugging the board to get RGB underglow effects to work.
 
-1. Try plugging the board in while holding the bootloader key. This will force 
-   it to boot only the bootloader without loading the firmware. Once this is
-   done, just reflash the board with the original firmware.
-2. Sometimes USB hubs can act weird, so try connecting the board directly
-   to your computer or plugging/unplugging the USB hub.
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).