123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112 |
- /*
- * Copyright 2017 skully <skullydazed@gmail.com>
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- */
- #pragma once
- #include "config_common.h"
- /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
- // #define DEBOUNCE 6
- /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
- //#define LOCKING_SUPPORT_ENABLE
- /* Locking resynchronize hack */
- //#define LOCKING_RESYNC_ENABLE
- /*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
- //#define FORCE_NKRO
- /*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
- /* disable debug print */
- //#define NO_DEBUG
- /* disable print */
- //#define NO_PRINT
- /* disable action features */
- //#define NO_ACTION_LAYER
- //#define NO_ACTION_TAPPING
- //#define NO_ACTION_ONESHOT
- /* Backlight configuration
- */
- #define BACKLIGHT_LEVELS 10
- // This is a 7-bit address, that gets left-shifted and bit 0
- // set to 0 for write, 1 for read (as per I2C protocol)
- // The address will vary depending on your wiring:
- // 0b1110100 AD <-> GND
- // 0b1110111 AD <-> VCC
- // 0b1110101 AD <-> SCL
- // 0b1110110 AD <-> SDA
- #define LED_DRIVER_ADDR_1 0b1110100
- #define I2C1_SCL_PIN B8
- #define I2C1_SDA_PIN B9
- #define LED_DRIVER_COUNT 1
- #define DRIVER_LED_TOTAL 71
- // LED Matrix Animation modes. Explicitly enabled
- // For full list of effects, see:
- // https://docs.qmk.fm/#/feature_led_matrix?id=led-matrix-effects
- #define ENABLE_LED_MATRIX_ALPHAS_MODS
- #define ENABLE_LED_MATRIX_BREATHING
- #define ENABLE_LED_MATRIX_BAND
- #define ENABLE_LED_MATRIX_BAND_PINWHEEL
- #define ENABLE_LED_MATRIX_BAND_SPIRAL
- #define ENABLE_LED_MATRIX_CYCLE_LEFT_RIGHT
- #define ENABLE_LED_MATRIX_CYCLE_UP_DOWN
- #define ENABLE_LED_MATRIX_CYCLE_OUT_IN
- #define ENABLE_LED_MATRIX_DUAL_BEACON
- #if defined(LED_MATRIX_KEYREACTIVE_ENABLED)
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_SIMPLE
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_WIDE
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_MULTIWIDE
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_CROSS
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_MULTICROSS
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_NEXUS
- # define ENABLE_LED_MATRIX_SOLID_REACTIVE_MULTINEXUS
- # define ENABLE_LED_MATRIX_SPLASH
- # define ENABLE_LED_MATRIX_MULTISPLASH
- #endif
- #define ENABLE_LED_MATRIX_WAVE_LEFT_RIGHT
- #define ENABLE_LED_MATRIX_WAVE_UP_DOWN
- #define AUDIO_PIN A5
- #define AUDIO_PIN_ALT A4
- #define AUDIO_PIN_ALT_AS_NEGATIVE
|