Makefile 3.0 KB

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374
  1. SUBPROJECT_DEFAULT = rev4
  2. # MCU name
  3. #MCU = at90usb1287
  4. MCU = atmega32u4
  5. # Processor frequency.
  6. # This will define a symbol, F_CPU, in all source code files equal to the
  7. # processor frequency in Hz. You can then use this symbol in your source code to
  8. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  9. # automatically to create a 32-bit value in your source code.
  10. #
  11. # This will be an integer division of F_USB below, as it is sourced by
  12. # F_USB after it has run through any CPU prescalers. Note that this value
  13. # does not *change* the processor frequency - it should merely be updated to
  14. # reflect the processor speed set externally so that the code can use accurate
  15. # software delays.
  16. F_CPU = 16000000
  17. #
  18. # LUFA specific
  19. #
  20. # Target architecture (see library "Board Types" documentation).
  21. ARCH = AVR8
  22. # Input clock frequency.
  23. # This will define a symbol, F_USB, in all source code files equal to the
  24. # input clock frequency (before any prescaling is performed) in Hz. This value may
  25. # differ from F_CPU if prescaling is used on the latter, and is required as the
  26. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  27. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  28. # at the end, this will be done automatically to create a 32-bit value in your
  29. # source code.
  30. #
  31. # If no clock division is performed on the input clock inside the AVR (via the
  32. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  33. F_USB = $(F_CPU)
  34. # Interrupt driven control endpoint task(+60)
  35. OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  36. # Boot Section Size in *bytes*
  37. # Teensy halfKay 512
  38. # Teensy++ halfKay 1024
  39. # Atmel DFU loader 4096
  40. # LUFA bootloader 4096
  41. # USBaspLoader 2048
  42. OPT_DEFS += -DBOOTLOADER_SIZE=4096
  43. # Build Options
  44. # change to "no" to disable the options, or define them in the Makefile in
  45. # the appropriate keymap folder that will get included automatically
  46. #
  47. BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
  48. MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
  49. EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
  50. CONSOLE_ENABLE ?= no # Console for debug(+400)
  51. COMMAND_ENABLE ?= yes # Commands for debug and configuration
  52. NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  53. BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
  54. MIDI_ENABLE ?= no # MIDI controls
  55. AUDIO_ENABLE ?= no # Audio output on port C6
  56. UNICODE_ENABLE ?= no # Unicode
  57. BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
  58. RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
  59. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  60. SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
  61. ifndef QUANTUM_DIR
  62. include ../../Makefile
  63. endif