qmk_firmware/keyboards/planck/rules.mk

# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000

#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Bootloader
#     This definition is optional, and if your keyboard supports multiple bootloaders of
#     different sizes, comment this out, and the correct address will be loaded 
#     automatically (+60). See bootloader.mk for all options.
ifeq ($(strip $(KEYBOARD)), planck/rev3)
    BOOTLOADER = atmel-dfu
endif
ifeq ($(strip $(KEYBOARD)), planck/rev4)
    BOOTLOADER = atmel-dfu
endif
ifeq ($(strip $(KEYBOARD)), planck/rev5)
    BOOTLOADER = qmk-dfu
endif
ifeq ($(strip $(KEYBOARD)), planck/light)
    BOOTLOADER = qmk-dfu
endif

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

# Build Options
#   change to "no" to disable the options, or define them in the Makefile in 
#   the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
CONSOLE_ENABLE = yes         # Console for debug(+400)
COMMAND_ENABLE = no        # Commands for debug and configuration
NKRO_ENABLE = yes            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
MIDI_ENABLE = yes            # MIDI controls
AUDIO_ENABLE = yes           # Audio output on port C6
UNICODE_ENABLE = no         # Unicode
BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
API_SYSEX_ENABLE = no

# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

LAYOUTS = ortho_4x12 planck_mit planck_grid

DEFAULT_FOLDER = planck/rev5