qmk_firmware/keyboards/ergodox_infinity/keymaps/halfkeyboard/rules.mk

# project specific files
SRC =	matrix.c \
	led.c

## chip/board settings
# - the next two should match the directories in
#   <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
# - For Teensies, FAMILY = KINETIS and SERIES is either
#   KL2x (LC) or K20x (3.0,3.1,3.2).
# - For Infinity KB, SERIES = K20x
MCU_FAMILY = KINETIS
MCU_SERIES = K20x

# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
#   or <this_dir>/ld/
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
# - LDSCRIPT =
#   - MKL26Z64 for Teensy LC
#   - MK20DX128 for Teensy 3.0
#   - MK20DX256 for Teensy 3.1 and 3.2
#   - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader
#   - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader
MCU_LDSCRIPT = MK20DX256BLDR8

# Startup code to use
#  - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
# - STARTUP =
#   - kl2x for Teensy LC
#   - k20x5 for Teensy 3.0 and Infinity 60%
#   - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox
MCU_STARTUP = k20x7

# Board: it should exist either in <chibios>/os/hal/boards/
#  or <this_dir>/boards
# - BOARD =
#   - PJRC_TEENSY_LC for Teensy LC
#   - PJRC_TEENSY_3 for Teensy 3.0
#   - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
#   - MCHCK_K20 for Infinity KB
#BOARD = MCHCK_K20
BOARD = PJRC_TEENSY_3_1

# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU  = cortex-m4

# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
ARMV = 7

# Vector table for application
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000

# Build Options
#   comment out to disable the options.
#

BOOTMAGIC_ENABLE = no  # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE  = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE  = yes # Audio control and System control(+450)
CONSOLE_ENABLE   = no  # Console for debug(+400)
COMMAND_ENABLE   = yes # Commands for debug and configuration
CUSTOM_MATRIX    = yes # Custom matrix file for the ErgoDox EZ
SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
NKRO_ENABLE      = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
UNICODE_ENABLE   = yes # Unicode
SWAP_HANDS_ENABLE = yes # Allow swapping hands of keyboard
STENO_ENABLE = yes  #enable plover steno mode
CUSTOM_MATRIX = yes # Custom matrix file
SERIAL_LINK_ENABLE = yes
VISUALIZER_ENABLE = yes
LCD_ENABLE = yes
BACKLIGHT_ENABLE = yes
LCD_BACKLIGHT_ENABLE = yes
MIDI_ENABLE = yes
MIDI_ADVANCED = yes
MUSIC_MODE = yes
RGBLIGHT_ENABLE = no

LCD_DRIVER = st7565
LCD_WIDTH = 128
LCD_HEIGHT = 32

LED_DRIVER = is31fl3731c
LED_WIDTH = 7
LED_HEIGHT = 7

LAYOUTS = ergodox