rules.mk 3.7 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110
  1. # project specific files
  2. SRC = matrix.c
  3. # MCU name
  4. #MCU = at90usb1287
  5. MCU = atmega32u4
  6. # Processor frequency.
  7. # This will define a symbol, F_CPU, in all source code files equal to the
  8. # processor frequency in Hz. You can then use this symbol in your source code to
  9. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  10. # automatically to create a 32-bit value in your source code.
  11. #
  12. # This will be an integer division of F_USB below, as it is sourced by
  13. # F_USB after it has run through any CPU prescalers. Note that this value
  14. # does not *change* the processor frequency - it should merely be updated to
  15. # reflect the processor speed set externally so that the code can use accurate
  16. # software delays.
  17. F_CPU = 16000000
  18. #
  19. # LUFA specific
  20. #
  21. # Target architecture (see library "Board Types" documentation).
  22. ARCH = AVR8
  23. # Input clock frequency.
  24. # This will define a symbol, F_USB, in all source code files equal to the
  25. # input clock frequency (before any prescaling is performed) in Hz. This value may
  26. # differ from F_CPU if prescaling is used on the latter, and is required as the
  27. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  28. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  29. # at the end, this will be done automatically to create a 32-bit value in your
  30. # source code.
  31. #
  32. # If no clock division is performed on the input clock inside the AVR (via the
  33. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  34. F_USB = $(F_CPU)
  35. # Interrupt driven control endpoint task(+60)
  36. OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  37. # Boot Section Size in *bytes*
  38. # Teensy halfKay 512
  39. # Teensy++ halfKay 1024
  40. # Atmel DFU loader 4096
  41. # LUFA bootloader 4096
  42. # USBaspLoader 2048
  43. #OPT_DEFS += -DBOOTLOADER_SIZE=4096
  44. # as per original hasu settings
  45. OPT_DEFS += -DBOOTLOADER_SIZE=4096
  46. # Build Options
  47. # comment out to disable the options.
  48. #
  49. BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  50. MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
  51. EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
  52. CONSOLE_ENABLE = yes # Console for debug(+400)
  53. COMMAND_ENABLE = yes # Commands for debug and configuration
  54. CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
  55. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  56. # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
  57. # NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  58. # BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
  59. # MIDI_ENABLE = yes # MIDI controls
  60. # UNICODE_ENABLE = yes # Unicode
  61. # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
  62. # HHKB_RN42_ENABLE = yes # Enable support for hasu's BT alt controller -- code borrowed from tmk source tree.
  63. # Either uncomment the HHKB_RN42_ENABLE line above, or run make enabling the
  64. # feature. Be sure to clean any existing build before trying to enable rn42
  65. # support. For example:
  66. #
  67. # make hhkb-keymap-clean
  68. # make hhkb-keymap-dfu HHKB_RN42_ENABLE=yes
  69. ifeq ($(strip $(HHKB_RN42_ENABLE)), yes)
  70. OPT_DEFS += -DHHKB_RN42_ENABLE
  71. # Support for the RN42 Bluetooth module. This is the BT module in Hasu's BT
  72. # HHKB Alt controller.
  73. RN42_DIR = rn42
  74. SRC += serial_uart.c \
  75. rn42/suart.S \
  76. rn42/rn42.c \
  77. rn42/rn42_task.c \
  78. rn42/battery.c \
  79. rn42/main.c
  80. VPATH += $(RN42_DIR)
  81. endif
  82. # debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
  83. # debug-on: all
  84. # debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
  85. # debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
  86. # debug-off: all