123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110 |
- # project specific files
- SRC = matrix.c
- # MCU name
- #MCU = at90usb1287
- MCU = atmega32u4
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
- # Interrupt driven control endpoint task(+60)
- OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- #OPT_DEFS += -DBOOTLOADER_SIZE=4096
- # as per original hasu settings
- OPT_DEFS += -DBOOTLOADER_SIZE=4096
- # Build Options
- # comment out to disable the options.
- #
- BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
- MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
- EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
- CONSOLE_ENABLE = yes # Console for debug(+400)
- COMMAND_ENABLE = yes # Commands for debug and configuration
- CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
- # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
- # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
- # NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
- # BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
- # MIDI_ENABLE = yes # MIDI controls
- # UNICODE_ENABLE = yes # Unicode
- # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
- # HHKB_RN42_ENABLE = yes # Enable support for hasu's BT alt controller -- code borrowed from tmk source tree.
- # Either uncomment the HHKB_RN42_ENABLE line above, or run make enabling the
- # feature. Be sure to clean any existing build before trying to enable rn42
- # support. For example:
- #
- # make hhkb-keymap-clean
- # make hhkb-keymap-dfu HHKB_RN42_ENABLE=yes
- ifeq ($(strip $(HHKB_RN42_ENABLE)), yes)
- OPT_DEFS += -DHHKB_RN42_ENABLE
- # Support for the RN42 Bluetooth module. This is the BT module in Hasu's BT
- # HHKB Alt controller.
- RN42_DIR = rn42
- SRC += serial_uart.c \
- rn42/suart.S \
- rn42/rn42.c \
- rn42/rn42_task.c \
- rn42/battery.c \
- rn42/main.c
- VPATH += $(RN42_DIR)
- endif
- # debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
- # debug-on: all
- # debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
- # debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
- # debug-off: all
|